|
|
PDF SiM3C144-B-GM Data sheet ( Hoja de datos )
| Número de pieza | SiM3C144-B-GM | |
| Descripción | 32-Bit Precision32 MCU | |
| Fabricantes | Silicon Laboratories | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SiM3C144-B-GM (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
www.DataSheet.co.kr
SiM3C1xx
High-Performance, Low-Power, 32-Bit Precision32™
MCU Family with up to 256 kB of Flash
32-bit ARM® Cortex™-M3 CPU
- 80 MHz maximum frequency
- Single-cycle multiplication, hardware division support
- Nested vectored interrupt control (NVIC) with 16 levels of
interrupt priority
Memory
- 32–256 kB Flash, in-system programmable
- 8–32 kB SRAM (including 4 kB retention SRAM)
- External bus interface supports up to 16 MB of external mem-
ory and a parallel LCD interface with QVGA resolution
Power Management
- Low drop-out (LDO) regulator
- Power-on reset circuit and brownout detectors
- 5-to-3.3 V voltage regulator supports up to 150 mA to drive the
device directly from up to 5 V supply
- Programmable external regulator supports up to 3.6 V,
1000 mA
- Multiple power modes supported for low power optimization
Clock Sources
- Internal oscillator with PLL: Fine frequency resolution up to
80 MHz; spread-spectrum mode for reduced EMI
- Low power internal oscillator: 20 MHz and 2.5 MHz modes
- Low frequency internal oscillator: 16.4 kHz
- External oscillators: Crystal, RC, C, CMOS and RTC Crystal
- Flexible clock divider: Reduce frequency by up to 128x from
any clock source
128/192/256-bit Hardware AES Encryption
- Hardware-supported Electronic Codebook (ECB), Cipher-Block
Chaining (CBC) and Counter (CTR) algorithms
- All cipher operations can be performed without any firmware
intervention for a set of 4-word blocks (up to 32 kB)
16/32-bit CRC
- Hardware support for common 32-bit and 16-bit polynomials
Timers/Counters
- 2 x 32-bit or 4 x 16-bit timers with capture/compare
- 2 x 16-bit, 2-channel counters with capture/compare/PWM
- 16-bit, 6-channel counter with capture/compare/PWM and
dead-time controller with differential outputs
- 16-bit low power timer/pulse counter operational in the lowest
power mode
- 32-bit real time clock (RTC) with multiple alarms
- Watchdog timer
Current-to-Voltage Converter
- Supports up to 6 mA input range
Supply Voltage
- 2.7 to 5.5 V (regulator enabled)
- 1.8 to 3.6 V (regulator disabled)
Low Power Features
- 85 nA current mode with voltage supply monitor enabled
- 350 nA current mode with RTC (internal oscillator)
- 620 nA current mode with RTC (external oscillator)
- 10 µs wakeup (lowest power mode); 1.5 µs analog setting time
- 275 µA/MHz active current
- Clocks can be gated off from unused peripherals to save power
2 x 12-Bit Analog-to-Digital Converters
- Up to 28 input channels
- Up to 250 ksps 12-bit mode or 1 Msps 10-bit mode
- Single, simultaneous, and interleaving modes supported
- Channel sequencer enables automatic multiplexing of multiple
channels without firmware intervention
- Internal VREF or external VREF supported
2 x 10-Bit Digital-to-Analog Converters
- DMA support for waveform generation
- Four-word circular buffer to enable 12-bit mode
16-Channel Capacitance-to-Digital Converter
- Supports buttons, sliders, wheels, and capacitive proximity
- Fast conversion time; <1 µA wake-on-touch average current
Two Low-Current Comparators
- Integrated 6-bit programmable reference voltage
- 400 nA current consumption in low power mode
16-Channel DMA Controller
- Supports ADC, DAC, I2C, I2S, SPI, USART, AES, EPCA,
capacitive sensing, external triggers, and timers
Up to 65 Flexible I/O
- Up to 59 contiguous GPIO with two priority crossbars providing
flexibility in pin assignments; 12 x 5 V tolerant GPIO
- Up to 6 programmable high drive capable (5–300 mA, 1.8–6 V)
I/O can drive LEDs, power MOSFETs, buzzers, etc.
Communication Interfaces
- 2 x USARTs and 2 x UARTs with IrDA and ISO7816 SmartCard
- 3 x SPIs, 2 x I2C, I2S (receive and transmit)
On-Chip Debugging
- Serial wire debug (SWD) and JTAG allow for full-speed, non-
intrusive debug
- Serial wire viewer (SWV) available in 64 / 80 / 92-pin packages
- Cortex-M3 embedded trace macrocell (ETM) in 80 / 92-pin
packages
Temperature Range: –40 to +85 °C
Package Options
- QFN options: 40-pin (6 x 6 mm), 64-pin (9 x 9 mm)
- TQFP options: 64-pin (10 x 10 mm), 80-pin (12 x 12 mm)
- LGA option: 92-pin (7 x 7 mm)
Preliminary Rev. 0.8 2/12
Copyright © 2012 by Silicon Laboratories
SiM3C1xx
This information applies to a product under development. Its characteristics and specifications are subject to change without notice.
Datasheet pdf - http://www.DataSheet4U.net/
1 page  
www.DataSheet.co.kr
SiM3C1xx
2. Typical Connection Diagrams
This section provides typical connection diagrams for SiM3C1xx devices.
2.1. Power
Figure 2.1 shows a typical connection diagram for the power pins of the SiM3C1xx devices when the internal
regulator is in use.
5 V (in)
1 uF and 0.1 uF bypass
capacitors required for
each power pin placed
as close to the pins as
possible.
SiM3C1xx Device
3.3 V (out)
VREGIN
VIOHD
VDD
VIO
VSS
VSSHD
VREGn
Figure 2.1. Connection Diagram with Voltage Regulator Used
Figure 2.2 shows a typical connection diagram for the power pins of the SiM3C1xx devices when the internal
regulator is not used.
SiM3C1xx Device
1 uF and 0.1 uF bypass
capacitors required for
each power pin placed
as close to the pins as
possible.
1.8-3.6 V (in)
VREGIN
VIOHD
VDD
VIO
VSS
VSSHD
VREGn
Figure 2.2. Connection Diagram with Voltage Regulator Not Used
Preliminary Rev. 0.8
5
Datasheet pdf - http://www.DataSheet4U.net/
5 Page 
www.DataSheet.co.kr
SiM3C1xx
Table 3.2. Power Consumption (Continued)
Parameter
Symbol
Conditions
Min Typ Max Units
Flash Current on VDD
Write Operation
IFLASH-W
——
8 mA
Erase Operation
IFLASH-E
— — 15 mA
Notes:
1. Perhipheral currents drop to zero when peripheral clock and peripheral are disabled, unless otherwise noted.
2. Currents are additive. For example, where IDD is specified and the mode is not mutually exclusive, enabling the
functions increases supply current by the specified amount.
3. Includes all peripherals that cannot have clocks gated in the Clock Control module.
4. Includes supply current from internal regulator and PLL0OSC (>20 MHz) or LPOSC0 (<=20 MHz).
5. Flash execution numbers use 2 wait states for 80 MHz and 0 wait states at 20 MHz or less.
6. RAM execution numbers use 0 wait states for all frequencies.
7. IDAC output current and IVC input current not included.
8. Bias current only. Does not include dynamic current from oscillator running at speed.
Table 3.3. Power Mode Wake Up Times
Parameter
Power Mode 3 Fast Wake Time
Power Mode 3 Wake Time
Power Mode 9 Wake Time
Symbol
tPM3FW
tPM3
tPM9
Conditions
Min Typ Max Units
— 425 —
µs
— 1.35 —
ms
— 12 — µs
Preliminary Rev. 0.8
11
Datasheet pdf - http://www.DataSheet4U.net/
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet SiM3C144-B-GM.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SiM3C144-B-GM | 32-Bit Precision32 MCU | Silicon Laboratories |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |