|
|
PDF MC10114 Data sheet ( Hoja de datos )
| Número de pieza | MC10114 | |
| Descripción | Triple Line Receiver | |
| Fabricantes | ON Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MC10114 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
MC10114
Triple Line Receiver
The MC10114 is a triple line receiver designed for use in sensing
differential signals over long lines. An active current source and
translated emitter follower inputs provide the line receiver with a
common mode noise rejection limit of one volt in either the positive or
the negative direction. This allows a large amount of common mode
noise immunity for extra long lines.
Another feature of the MC10114 is that the OR outputs go to a logic
low level whenever the inputs are left floating. The outputs are each
capable of driving 50 ohm transmission lines.
This device is useful in high speed central processors,
minicomputers, peripheral controllers, digital communication
systems, testing and instrumen– tation systems. The MC10114 can
also be used for MOS to MECL interfacing and it is ideal as a sense
amplifier for MOS RAM’s.
A VBB reference is provided which is useful in making the
MC10114 a Schmit trigger, allowing single–ended driving of the
inputs, or other applications where a stable reference voltage is
necessary. See MECL Design Handbook (HB205) pages 226 and 228.
• PD = 145 mW typ/pkg
• tpd = 2.4 ns typ (Single Ended Input)
• tpd = 2.0 ns typ (Differential Input)
• tr, tf = 2.1 ns typ (20%–80%)
LOGIC DIAGRAM
www.DataSheet4U.com
42
53
96
10 7
12 14 VCC1 = PIN 1
13 15 VCC2 = PIN 16
11 VEE = PIN 8
VBB*
*VBB to be used to supply bias to the MC10114 only and bypassed (when used) with
0.01 µF to 0.1 µF capacitor to ground (0 V). VBB can source < 1.0 mA.
When the input pin with the bubble goes positive, its respective output pin with
bubble goes positive.
DIP PIN ASSIGNMENT
VCC1
AOUT
AOUT
AIN
AIN
BOUT
BOUT
VEE
1
2
3
4
5
6
7
8
16 VCC2
15 COUT
14 COUT
13 CIN
12 CIN
11 VBB
10 BIN
9 BIN
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion Tables on page 18
of the ON Semiconductor MECL Data Book (DL122/D).
http://onsemi.com
CDIP–16
L SUFFIX
CASE 620
PDIP–16
P SUFFIX
CASE 648
PLCC–20
FN SUFFIX
CASE 775
MARKING
DIAGRAMS
16
MC10114L
AWLYYWW
1
16
MC10114P
AWLYYWW
1
1
10114
AWLYYWW
A = Assembly Location
WL = Wafer Lot
YY = Year
WW = Work Week
ORDERING INFORMATION
Device
Package
Shipping
MC10114L
CDIP–16
25 Units / Rail
MC10114P
PDIP–16
25 Units / Rail
MC10114FN
PLCC–20
46 Units / Rail
© Semiconductor Components Industries, LLC, 2002
January, 2002 – Rev. 7
1
Publication Order Number:
MC10114/D
1 page  
MC10114
PACKAGE DIMENSIONS
PLCC–20
FN SUFFIX
PLASTIC PLCC PACKAGE
CASE 775–02
ISSUE C
B 0.007 (0.180) M T L-M S N S
–N– Y BRK
D
U 0.007 (0.180) M T L-M S N S
–L– –M– Z
W
20 1
V
D X G1 0.010 (0.250) S T L-M S N S
VIEW D–D
A 0.007 (0.180) M T L-M S N S
Z
R 0.007 (0.180) M T L-M S N S
K1
H 0.007 (0.180) M T L-M S N S
C
E
G
G1
0.010 (0.250) S T L-M S
0.004 (0.100)
J –T– SEATING
PLANE
VIEW S
NS
K
F
VIEW S
0.007 (0.180) M T L-M S N S
NOTES:
1. DATUMS -L-, -M-, AND -N- DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS PLASTIC
BODY AT MOLD PARTING LINE.
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM -T-, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE MOLD
FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250)
PER SIDE.
4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN THE
PACKAGE BOTTOM BY UP TO 0.012 (0.300).
DIMENSIONS R AND U ARE DETERMINED AT THE
OUTERMOST EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS,
GATE BURRS AND INTERLEAD FLASH, BUT
INCLUDING ANY MISMATCH BETWEEN THE TOP
AND BOTTOM OF THE PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037 (0.940).
THE DAMBAR INTRUSION(S) SHALL NOT CAUSE
THE H DIMENSION TO BE SMALLER THAN 0.025
(0.635).
INCHES
MILLIMETERS
DIM MIN MAX MIN MAX
A 0.385 0.395 9.78 10.03
B 0.385 0.395 9.78 10.03
C 0.165 0.180 4.20 4.57
E 0.090 0.110 2.29 2.79
F 0.013 0.019 0.33 0.48
G 0.050 BSC
1.27 BSC
H 0.026 0.032 0.66 0.81
J 0.020 --- 0.51 ---
K 0.025 --- 0.64 ---
R 0.350 0.356 8.89 9.04
U 0.350 0.356 8.89 9.04
V 0.042 0.048 1.07 1.21
W 0.042 0.048 1.07 1.21
X 0.042 0.056 1.07 1.42
Y --- 0.020 --- 0.50
Z 2_ 10_ 2 _ 10 _
G1 0.310 0.330 7.88 8.38
K1 0.040 --- 1.02 ---
http://onsemi.com
5
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet MC10114.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MC10110 | Dual 3-Input/3-Output OR Gate | ON Semiconductor |
| MC10110L | Dual 3-Input/3-Ouput OR Gate |  Motorola Semiconductors |
| MC10110P | Dual 3-Input/3-Ouput OR Gate | Motorola Semiconductors |
| MC10111 | Dual 3-Input/3-Output NOR Gate | Motorola Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |