DataSheet.es    


PDF AN5792 Data sheet ( Hoja de datos )

Número de pieza AN5792
Descripción Horizontal Signal Processing ICs for CRT Display
Fabricantes Panasonic Semiconductor 
Logotipo Panasonic Semiconductor Logotipo



Hay una vista previa y un enlace de descarga de AN5792 (archivo pdf) en la parte inferior de esta página.


Total 5 Páginas

No Preview Available ! AN5792 Hoja de datos, Descripción, Manual

ICs for TV
AN5790N, AN5792
Horizontal Signal Processing ICs for CRT Display
s Overview
The AN5790N and AN5792 are the intergrated circuits
designed for CRT display horizontal signal processing cir-
cuits.
s Features
Horizontal synchronous signal is available in both polar-
ities.
Wide range of horizontal osciallation frequency : 14kHz
to 60kHz.
Output pulse width : 2µs to 40µs
Package
AN5790N...NF-12S(12-Pin SIL plastic package)
AN5792...F-12S (12-Pin SIL plastic package with fin)
AN5790N
7.9±0.3
3.5±0.25
1.2±0.25
12
11
10
9
8
7
6
5
4
3
2
1
0.45
+
0.1
0.05
1.7±0.25
Unit : mm
1.7±0.25
12-Pin SIL Plastic Package (12-SIP)
AN5792
5.8±0.25 7.9±0.3
12
11
10
9
8
7
6
5
4
3
2
1
3.5±0.25
1.2±0.25
Unit : mm
s Block Diagram
1.7±0.25
12-Pin SIL Plastic Package with Fin (12-SIF (f))
VCC
65
1
Polarity
Switch
2
X-ray
Protector
Pre-Amp.
8
AFC
Hor. Osc.
34
12 11
PulseWidth
Adjustment
7 GND
9 10

1 page




AN5792 pdf
Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other
company which may arise as a result of the use of technical information described in this book.
(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office
equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-
ucts may directly jeopardize life or harm the human body.
Any applications other than the standard applications intended.
(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product
Standards in advance to make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita
Electric Industrial Co., Ltd.

5 Page










PáginasTotal 5 Páginas
PDF Descargar[ Datasheet AN5792.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
AN5790NHorizontal Signal Processing ICs for CRT DisplayPanasonic Semiconductor
Panasonic Semiconductor
AN5791PHASE SHIFT CIRCUIT FOR CRT DISPLAYSPanasonic Semiconductor
Panasonic Semiconductor
AN5792Horizontal Signal Processing ICs for CRT DisplayPanasonic Semiconductor
Panasonic Semiconductor
AN5795NKDeflection Signal Processing IC for CRTPanasonic Semiconductor
Panasonic Semiconductor

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar