|
|
Número de pieza | VND7050AJ12 | |
Descripción | Double channel high-side driver | |
Fabricantes | STMicroelectronics | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de VND7050AJ12 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! VND7050AJ12
Double channel high-side driver with CurrentSense analog
feedback for automotive applications
Datasheet - production data
PowerSSO-12
GAPG040515 1112CFT
Features
Max transient supply voltage
VCC
40 V
Operating voltage range
VCC 4 V to 28 V
Minimum cranking supply
voltage (VCC decreasing)
VUSD_Cranking 2.85 V
Typ. on-state resistance
(per Ch)
RON 50 mΩ
Current limitation (typ)
ILIMH
30 A
Standby current (max)
ISTBY
0.5 µA
• Automotive qualified
• Extreme low voltage operation for deep cold
cranking applications (compliant with LV124,
revision 2013)
• General
− Double channel smart high-side driver
with CurrentSense analog feedback
− Very low standby current
− Compatible with 3 V and 5 V CMOS
outputs
• CurrentSense diagnostic functions
− Multiplexed analog feedback of: load
current with high precision proportional
current mirror
− Overload and short to ground (power
limitation) indication
− Thermal shutdown indication
− Off-state open-load detection
− Output short to VCC detection
− Sense enable/ disable
• Protections
− Undervoltage shutdown
− Overvoltage clamp
− Load current limitation
− Self limiting of fast thermal transients
− Loss of ground and loss of VCC
− Reverse battery with external
components
− Electrostatic discharge protection
Applications
• All types of Automotive resistive, inductive
and capacitive loads
• Specially intended for Automotive Signal
Lamps (up to P27W or SAE1156 or LED
Rear Combinations)
Description
The device is a double channel high-side driver
manufactured using ST proprietary VIPower®
technology and housed in PowerSSO-12
package. The device is designed to drive 12 V
automotive grounded loads through a 3 V and
5 V CMOS compatible interface, providing
protection and diagnostics.
The device integrates advanced protective
functions such as load current limitation, overload
active management by power limitation and
overtemperature shutdown.
A current sense delivers high precision
proportional load current sense in addition to the
detection of overload and short circuit to ground,
short to VCC and off-state open-load.
A sense enable pin allows off-state diagnosis to
be disabled during the module low-power mode
as well as external sense resistor sharing among
similar devices.
September 2015
DocID027585 Rev 3
This is information on a product in full production.
1/43
www.st.com
1 page VND7050AJ12
Block diagram and pin description
1 Block diagram and pin description
Figure 1: Block diagram
Table 1: Pin functions
Name
Function
VCC Battery connection.
OUTPUT0,1 Power output.
GND
Ground connection. Must be reverse battery protected by an external diode/resistor
network.
INPUT0,1
Voltage controlled input pins with hysteresis, compatible with 3 V and 5 V CMOS
outputs. They control output switch state.
CurrentSense
Multiplexed analog sense output pin; it delivers a current proportional to the load
current.
SEn
Active high compatible with 3 V and 5 V CMOS outputs pin; it enables the
CurrentSense diagnostic pin.
SEL
Active high compatible with 3 V and 5 V CMOS outputs pin; it addresses the
CurrentSense multiplexer.
DocID027585 Rev 3
5/43
5 Page VND7050AJ12
7 V < VCC < 18 V; -40°C < Tj < 150°C
Table 9: Protections
Electrical specification
Symbol
Parameter
Test conditions
Min. Typ. Max. Unit
ILIMH DC short circuit current
VCC = 13 V
4 V < VCC < 18 V (1)
21 30 42
42 A
ILIML
Short circuit current during
thermal cycling
VCC = 13 V; TR < Tj < TTSD
10
TTSD
TR
TRS
Shutdown temperature
Reset temperature(1)
Thermal reset of fault
diagnostic indication
VSEn = 5 V
150 175
TRS + 1 TRS + 7
200
135 °C
THYST
Thermal hysteresis (TTSD -
TR)(1)
ΔTJ_SD Dynamic temperature
Turn-off output voltage
VDEMAG clamp
VON
Output voltage drop
limitation
Tj = -40 °C; VCC = 13 V
IOUT = 2 A; L = 6 mH;
Tj = -40 °C
IOUT = 2 A; L = 6 mH;
Tj = 25 °C to +150 °C
IOUT = 0.2 A
VCC - 38
7
60
K
V
VCC - 41 VCC - 46 VCC - 52
20 mV
Notes:
(1)Parameter guaranteed by design and characterization; not subject to production test.
Table 10: CurrentSense
7 V < VCC < 18 V; -40°C < Tj < 150°C
Symbol
Parameter
Test conditions
Min. Typ. Max. Unit
VSEn = 0 V; ISENSE = 1 mA -17
-12 V
VSENSE_CL CurrentSense clamp voltage
VSEn = 0 V; ISENSE = -1 mA
7
V
CurrentSense characteristics
KOL
IOUT/ISENSE
dKcal/Kcal(1)(2)
Current sense ratio drift at
calibration point
KLED
IOUT/ISENSE
dKLED/KLED(1)(2) Current sense ratio drift
K0 IOUT/ISENSE
dK0/K0(1)(2) Current sense ratio drift
K1 IOUT/ISENSE
IOUT = 0.01 A;
VSENSE = 0.5 V; VSEn = 5 V
IOUT = 0.01 A to 0.05 A;
Ical = 30 mA;
VSENSE = 0.5 V; VSEn = 5 V
IOUT = 0.05 A;
VSENSE = 0.5 V; VSEn = 5 V
IOUT = 0.05 A;
VSENSE = 0.5 V; VSEn = 5 V
IOUT = 0.2 A;
VSENSE = 0.5 V; VSEn = 5 V
IOUT = 0.2 A;
VSENSE = 0.5 V; VSEn = 5 V
IOUT = 0.4 A; VSENSE = 4 V;
VSEn = 5 V
440
-30 30
530 1450 2200
-25 25
830 1400 1935
-20 20
915 1300 1700
%
%
%
DocID027585 Rev 3
11/43
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet VND7050AJ12.PDF ] |
Número de pieza | Descripción | Fabricantes |
VND7050AJ12 | Double channel high-side driver | STMicroelectronics |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |