|
|
PDF LCCM1206 Data sheet ( Hoja de datos )
| Número de pieza | LCCM1206 | |
| Descripción | Chip Inductors | |
| Fabricantes | AVX | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LCCM1206 (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
|
No Preview Available !
Chip Inductors
LCCM Series – Chip Common Mode Filter
FEATURES
• Small wire wound chip inductor with ferrite core and 2 common
mode lines.
• Highly effective in noise suppression
• High common-mode impedance at noise band an low
differential mode impedance at signal band factor. There is
almost no distortion in high-speed signals.
• Operating temperature -40°C ~ 85°C.
CONSTRUCTION
APPLICATIONS
• EMI suppression for electronic devices.
• USB line in personal computers and peripherals.
• IEEE 1394 line for personal computers, DVC, and STB
• LCD Panels.
• Low-Voltage Differential Signal (LVDS)
Terminal
Ferrite
Enamel-insulated
Wire
DIMENSIONS
E
AF
E
B
C
K HK
I
J
I
Type
LCCM0805
LCCM1206
G
Size
(inch)
0805
1206
A B CE
2.00 ± 0.20
1.20 ± 0.20
(0.079 ± 0.008) (0.047 ± 0.008)
3.20 ± 0.20
1.60 ± 0.20
(0.126 ± 0.008) (0.063 ± 0.008)
1.20 ± 0.20
(0.047 ± 0.008)
1.80 ± 0.20
(0.071 ± 0.008)
0.45
(0.018)
0.60
(0.024)
F
1.20
(0.047)
2.00
(0.079)
G
0.40
(0.016)
0.60
(0.024)
H
0.80
(0.031)
1.60
(0.063)
I
0.40
(0.016)
0.60
(0.024)
J
0.40
(0.016)
0.40
(0.016)
mm (inches)
K
0.90
(0.035)
1.05
(0.041)
Weight (g)
(1000pcs)
19
53.3
HOW TO ORDER
LC
CM
0805 M
101
G
T AR
Family
Series
LC = Chip Inductor CM = Common Mode
Size
0805
1206
Tolerance
M = 20%
Impedance
100 = 10 Ω
101 = 100 Ω
102 = 1000 Ω
Style
G = Standard
Termination
Special
Packaging
T = Sn Plating A = Standard R = 7" Reel
2
1 page  
Chip Inductors
LCCM Series – Chip Common Mode Filter
ENVIRONMENTAL CHARACTERISTICS
ELECTRICAL PERFORMANCE TEST
Items
Impedance
DC Resistance DCR
Requirement
Withstand Voltage (VDC)
Rated Voltage (VDC)
Refer to standard electrical
characteristic spec.
Component should not
be damaged
Insulation Resistance (I.R)
MECHANICAL PERFORMANCE TEST
Items
Component Adhesion
(Push Test)
Requirement
Base: 0805 2 Lbs
Cover: 0805 1 Lbs
Base: 1206 4 Lbs
Cover: 1206 2 Lbs
Drop
Solderability
Vibration Test
(Low Frequency)
Component should not
be damaged
The terminal should at least
be 90% covered with solder
Component should not
be damaged
Test Conditions I Test Methods
LCR Meter HP 4291B
Micro-Ohm meter (GOM-801G)
Test Voltage: 2.5 Times Rated Voltage
Testing Time: 60 seconds
Charge Current: 0.5mA
Test Voltage: Rated Voltage
Testing Time: 1 to 5 seconds
Charge Current: 1mA
Charge Current: 1minute
10M ohm min.
Test Conditions I Test Methods
The component should be soldered (232°C ± 5°C
for 10 sec.) to tinned copper substrate
Applied force gauge to the side of component
It must withstand force of 2 or 4 pounds without
failure of the component.
Dropping chip by each side and corner.
Drop 10 times in total
Drop height: 100 cm
Drop weight: 125 g
The component shall be dipped in a
melted solder bath at 245 ±5°C for 3 seconds
1. Amplitude: 1.5 m/m
2. Frequency: 10-55-10Hz (1min.)
3. Direction: X, Y, Z
4. Duration: 2 Hrs/X, Y, Z
MECHANICAL PERFORMANCE TEST
Items
Requirement
Low Temperature Storage
Thermal Shock
High Temperature Storage
Impedance change: Within± 20%
Without distinct damage
in appearance
Humidity
High Temperature Load Life
Low Temperature Load Life
There should be no evidence of
short or open circuit
Test Conditions I Test Methods
1. Temp: -40 ±2°C
2. Time: 1000±48 Hours
3. Component should be tested after 1 hour
at room temperature
ROOM TEMP
15 MINS
-25 ± 2ºC
30 MINS
Total: 5 Cycles
ROOM TEMP
15 MINS
85 ± 2ºC
30 MINS
1. Temp: 85 ± 2°C
2. Time: 1000 ± 48 Hours
3. Component should be tested after 1 hour
at room temperature
1. Temp: 40 ± 2°C
2. R.H. : 90 — 95%
3. Time: 48 ±2 Hours
1. Temp: 85 ± 2°C
2. Time: 96 ± 12 Hours
3. Load: Allowed DC Current
1. Temp: -40 ± 2°C
2. Time: 96 ± 12 Hours
3. Load: Allowed DC Current
6
5 Page | ||
| Páginas | Total 6 Páginas | |
| PDF Descargar | [ Datasheet LCCM1206.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LCCM1206 | Chip Inductors | AVX |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |