|
|
Número de pieza | IPS160H | |
Descripción | Single high-side switch | |
Fabricantes | STMicroelectronics | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de IPS160H (archivo pdf) en la parte inferior de esta página. Total 26 Páginas | ||
No Preview Available ! IPS160H
Single high-side switch
Datasheet - preliminary data
Features
RDS(on)
0.060 Ω
PowerSSO12
IOUT
2.5 A
VCC
65 V
8 V to 60 V operating voltage range
Minimum output current limitation: 2.6 A
Non-dissipative short-circuit protection (cut-
off)
Programmable cut-off delay time using
external capacitor
Diagnostic signalization for: open load in off-
state, cut-off and junction thermal shutdown
Fast demagnetization of inductive load
Ground disconnection protection
VCC disconnection protection
Undervoltage lock-out
Designed to meet IEC 61131-2
PSSO12 package
Applications
Programmable logic control
Industrial PC peripheral input/output
Numerical control machines
SIL applications
Description
The IPS160H is a monolithic device which can
drive capacitive, resistive or inductive loads with
one side connected to ground; it is specifically
designed to match safety integrity level (SIL)
applications.
Built-in thermal shutdown protects the chip
against overtemperature and short-circuit. In
order to minimize the power dissipation when the
output is shorted, a non-dissipative short-circuit
protection (cut-off) is implemented, it limits both
the output average current value and,
consequently, the device overheating. The DIAG
common diagnostic pin reports the thermal
shutdown, open load in off-state and cut-off.
Cut-off delay time can be programmed by an
external capacitor.
Table 1: Device summary
Order code
Package
Packing
IPS160H
PowerSSO12
Tube
IPS160HTR PowerSSO12 Tape and reel
November 2015
DocID027563 Rev 2
This is preliminary information on a new product now in development
or undergoing evaluation. Details are subject to change without notice.
1/26
www.st.com
1 page IPS160H
1 Block diagram
Figure 1: Block diagram
Block diagram
IN
DIAG
Undervoltage
detection
Vcc clamp
Output clamp
GND
Current limitation
cut -off
Open load in off-state
Junction
Overtemperature
Vcc
OUT
CoD
GIPG1702151307LM
DocID027563 Rev 2
5/26
5 Page IPS160H
Symbol
VIL
VIH
VI(HYST)
IIN
Parameter
Table 8: Logic inputs
Test conditions
Input low level voltage
Input high level voltage
Input hysteresis voltage
Input current
VCC = VIN = 36 V
VCC = VIN = 60 V
Electrical characteristics
Min.
2.2
Typ.
0.4
Max.
0.8
200
550
Unit
V
μA
Symbol
Vclamp
Vdemag
VOLoff
tBKT
VDIAG
IDIAG
ILIM
tcoff
tres
TJSD
TJHYST
Table 9: Protection and diagnostic
Parameter
Test conditions
Min.
Typ.
Max.
VCC active clamp
Demagnetization
voltage
ICC = 10 mA
IOUT = 0.5 A; load =1
mH
65.5 68.5 71.5
VCC-71.5 VCC-68.5 VCC-65.5
Open load (off-state)
or short to VCC
detection threshold
24
Open load blanking
time
200
Voltage drop on
DIAG
DIAG pin leakage
current
Output current
limitation
IDIAG = 4 mA
VCC ≤ 36 V
36 V ˂ VCC ≤ 60 V
VCC ≤ 32 V, RLOAD ≤
10 mΩ
2.6
1
80
180
4.3
Cut-off current delay
time
Output stage restart
delay time
Programmable by the
external capacitor on
CoD pin. Cut-off is
disabled when CoD
pin is connected to
GND through 1 kΩ
resistor.
TJ˂ TJSD
TJ˂ TJSD
50xCCOD[nf] ± 35%(1)
32xtcoff [μs]± 40%
Junction temperature
shutdown
150 170 190
Junction temperature
thermal hysteresis
15
Unit
V
μs
V
μA
A
μs
°C
Notes:
(1)The formula is guaranteed in the range 10 nF ≤ CCOD ≤ 100 nF.
DocID027563 Rev 2
11/26
11 Page |
Páginas | Total 26 Páginas | |
PDF Descargar | [ Datasheet IPS160H.PDF ] |
Número de pieza | Descripción | Fabricantes |
IPS160H | Single high-side switch | STMicroelectronics |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |