|
|
PDF SDN135 Data sheet ( Hoja de datos )
| Número de pieza | SDN135 | |
| Descripción | Photodiode | |
| Fabricantes | Solid State Optronic | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SDN135 (archivo pdf) en la parte inferior de esta página. Total 11 Páginas | ||
|
No Preview Available !
SDN135
Analog High Speed Optocoupler
1MBd, Photodiode with Transistor Output
Description
The SDN135 is a high speed optocoupler consisting of an
infrared GaAs LED optically coupled through a high
isolation barrier to an integrated high speed transistor and
photodiode.
Separate access to the photodiode and transistor allow
users to reduce base-collector capacitance, enabling much
higher switching speeds. Signals with frequencies of up to
2.0MHz can be switched, giving the SDN135 a much
broader application range than traditional optocouplers.
The SDN135 comes standard in an 8 pin DIP package.
Applications
High Speed Logic Ground Isolation
Replace Slower Speed Optocouplers
Line Receivers
Power Transistor Isolation
Pulse Transformer Replacement
Switch Mode Power Supplies
High Voltage Insulation
Ground Isolation – Analog Signals
Schematic Diagram
NC 1
8 VCC
Anode 2
7 VB
Cathode 3
6 VO
NC 4
5 Ground
SDN135
Truth Table
(Positive Logic)
LED
ON
OFF
VO
LOW
HIGH
** A 0.1μF bypass Capacitor must be connected between pins 5 & 8
(GND & VCC)
Features
TTL Compatible
High Bit Rate: 1Mb/s
Bandwidth: 2.0MHz
Open Collector Output
High Isolation Voltage (5000VRMS)
High Common Mode Interference Immunity
RoHS / Pb-Free / REACH Compliant
Agency Approvals
UL / C-UL:
VDE:
File # E201932
File # 40035191 (EN 60747-5-2)
Absolute Maximum Ratings
The values indicated are absolute stress ratings. Functional
operation of the device is not implied at these or any
conditions in excess of those defined in electrical
characteristics section of this document. Exposure to
absolute Maximum Ratings may cause permanent damage
to the device and may adversely affect reliability.
Storage Temperature …………………………..-55 to +125°C
Operating Temperature …………………………-40 to +85°C
Continuous Input Current ………………………………..40mA
Transient Input Current ………………….……………..400mA
Reverse Input Control Voltage …………..…………………5V
Input Power Dissipation…………………………………40mW
Peak Output Current (Pin 6) …………………………….16mA
Max Emitter-Base Reverse Voltage (Pin 5-7)……………..5V
Max Supply Voltage (Pin 8-5) ……………………………..15V
Max Output Voltage (Pin 6-5) ……………………………..15V
Max Base Current (Pin 7) …………………………………5mA
Output Power Dissipation ……………………………..100mW
Ordering Information
Part Number Description
SDN135
SDN135-H
SDN135-S
SDN135-STR
8 pin DIP, (50/Tube)
0.40” (10.16mm) Lead Spacing (VDE0884)
8 pin SMD, (50/Tube)
8 pin SMD, Tape and Reel (1000/Reel)
NOTE: Suffixes listed above are not included in marking on
device for part number identification
© 2012 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page # 1
SDN135/H/S/TR
Rev 1.10 (08/09/2012)
001510
1 page  
SDN135
Analog High Speed Optocoupler
1MBd, Photodiode with Transistor Output
SDN135 Performance & Characteristics Plots, TA = 25°C, VCC=5V (unless otherwise specified)
Figure 9: Propagation Delay Time (tp) vs. Temperature (°C)
Figure 10: Load Resistance (RL) vs. Propagation Delay Time (tp)
TPLH SDN135
TPLH SDN136
TPHL SDN136
TPHL SDN135
© 2012 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page # 5
SDN135/H/S/TR
Rev 1.10 (08/09/2012)
001510
5 Page 
SDN135
Analog High Speed Optocoupler
1MBd, Photodiode with Transistor Output
DISCLAIMER
Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO
reserves the right to make changes to product description, specifications at any time without further notices.
SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither circuit patent
licenses nor indemnity are expressed or implied.
Except as specified in SSO’s Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we make no other
warranty, expressed or implied, including merchantability and fitness for particular use.
LIFE SUPPORT POLICY
SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or
death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any and all
damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the
body, or (b) support or sustain life, and (c) whose failure to perform when used properly in accordance with instructions for use can be
reasonably expected to result in significant injury to the user, or (d) a critical component of a life support device or system whose failure can be
reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness.
© 2012 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page # 11
SDN135/H/S/TR
Rev 1.10 (08/09/2012)
001510
11 Page | ||
| Páginas | Total 11 Páginas | |
| PDF Descargar | [ Datasheet SDN135.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SDN135 | Photodiode | Solid State Optronic |
| SDN136 | Photodiode | Solid State Optronic |
| SDN137 | Digital High Speed Optocoupler | Solid State Optronic |
| SDN138 | Photodiode | Solid State Optronic |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |