|
|
PDF SDN138 Data sheet ( Hoja de datos )
| Número de pieza | SDN138 | |
| Descripción | Photodiode | |
| Fabricantes | Solid State Optronic | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SDN138 (archivo pdf) en la parte inferior de esta página. Total 11 Páginas | ||
|
No Preview Available !
SDN138
Analog High Speed Optocoupler
100KBd, Photodiode with Darlington Output
Description
The SDN138 consists of a highly efficient AlGaAs
Light Emitting Diode and an integrated high gain
photo detector to provide extremely high current
transfer ratio between input and output. Separate
pins for the photodiode and output stage result in TTL
compatible saturation voltage and high speed
operation. Where desired the VCC and VO terminals
may be tied together to achieve conventional photo
Darlington operation. A base access terminal allows
a gain bandwidth adjustment to be made.
The SDN138 comes standard in an 8 pin DIP package.
Applications
Digital Logic Ground Isolation
Replace Slower Speed Optocouplers
Low Input Current Line Receivers
Ring Detector Circuitry
Loop Current Receiver
High Common Mode Noise Line Receiver
Schematic Diagram
NC 1
8 VCC
Anode 2
7 VB
Cathode 3
6 VO
NC 4
5 Ground
SDN138
Truth Table
(Positive Logic)
LED
ON
OFF
VO
LOW
HIGH
** A 0.1μF bypass Capacitor must be connected between pins 5 & 8
(GND & VCC)
Features
TTL Compatible
Low Control Current Requirements (0.5mA)
High Output Current (60mA)
High CTR Performance (2000%)
High Isolation Voltage (5000VRMS)
Instantaneous Common Mode Rejection (10kV/S)
RoHS / Pb-Free / REACH Compliant
Agency Approvals
UL / C-UL:
VDE:
File # E201932
File # 40035191 (EN 60747-5-2)
Absolute Maximum Ratings
The values indicated are absolute stress ratings. Functional
operation of the device is not implied at these or any
conditions in excess of those defined in electrical
characteristics section of this document. Exposure to
absolute Maximum Ratings may cause permanent damage
to the device and may adversely affect reliability.
Storage Temperature …………………………..-55 to +125°C
Operating Temperature …………………………-40 to +85°C
Continuous Input Current ………………………………..40mA
Transient Input Current ………………….……………..400mA
Reverse Input Control Voltage …………………..…………5V
Max Input Current (IF) …………………………………..40mA
Input Power Dissipation ……..…………………………40mW
Supply Voltage, Output Voltage (VCC, VO) …….…-0.5 to 7V
Average Output Current (IO) ………………...………….50mA
Emitter-Base Reverse Voltage (VER) …………………..0.5V
Output Power Dissipation …………………………..100mW
Ordering Information
Part Number Description
SDN138
SDN138-H
SDN138-S
SDN138-STR
8 pin DIP, (50/Tube)
0.40” (10.16mm) Lead Spacing (VDE0884)
8 pin SMD, (50/Tube)
8 pin SMD, Tape and Reel (1000/Reel)
NOTE: Suffixes listed above are not included in marking on
device for part number identification
© 2012 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page # 1
SDN138/H/S/TR
Rev 1.10 (08/10/2012)
001513
1 page  
SDN138
Analog High Speed Optocoupler
100KBd, Photodiode with Darlington Output
SDN138 Performance & Characteristics Plots, TA = 25°C (unless otherwise specified)
Figure 9: Non-Saturated Rise & Fall Times vs. Load Resistance
Figure 10: Logic LOW Supply Current vs. Forward Current
© 2012 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page # 5
SDN138/H/S/TR
Rev 1.10 (08/10/2012)
001513
5 Page 
SDN138
Analog High Speed Optocoupler
100KBd, Photodiode with Darlington Output
DISCLAIMER
Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO
reserves the right to make changes to product description, specifications at any time without further notices.
SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither circuit patent
licenses nor indemnity are expressed or implied.
Except as specified in SSO’s Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we make no other
warranty, expressed or implied, including merchantability and fitness for particular use.
LIFE SUPPORT POLICY
SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or
death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any and all
damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the
body, or (b) support or sustain life, and (c) whose failure to perform when used properly in accordance with instructions for use can be
reasonably expected to result in significant injury to the user, or (d) a critical component of a life support device or system whose failure can be
reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness.
© 2012 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page # 11
SDN138/H/S/TR
Rev 1.10 (08/10/2012)
001513
11 Page | ||
| Páginas | Total 11 Páginas | |
| PDF Descargar | [ Datasheet SDN138.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SDN135 | Photodiode | Solid State Optronic |
| SDN136 | Photodiode | Solid State Optronic |
| SDN137 | Digital High Speed Optocoupler | Solid State Optronic |
| SDN138 | Photodiode | Solid State Optronic |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |