|
|
PDF NX3L2G66 Data sheet ( Hoja de datos )
| Número de pieza | NX3L2G66 | |
| Descripción | Dual low-ohmic single-pole single-throw analog switch | |
| Fabricantes | NXP Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de NX3L2G66 (archivo pdf) en la parte inferior de esta página. Total 22 Páginas | ||
|
No Preview Available !
NX3L2G66
Dual low-ohmic single-pole single-throw analog switch
Rev. 8 — 7 February 2013
Product data sheet
1. General description
The NX3L2G66 is a dual low-ohmic single-pole single-throw analog switch. Each switch
has two input/output terminals (nY and nZ) and an active HIGH enable input (nE). When
pin nE is LOW, the analog switch is turned off.
Schmitt trigger action at the enable input (nE) makes the circuit tolerant to slower input
rise and fall times. The NX3L2G66 allows signals with amplitude up to VCC to be
transmitted from nY to nZ; or from nZ to nY. Its low ON resistance (0.5 ) and flatness
(0.13 ) ensures minimal attenuation and distortion of transmitted signals.
2. Features and benefits
Wide supply voltage range from 1.4 V to 4.3 V
Very low ON resistance (peak):
1.6 (typical) at VCC = 1.4 V
1.0 (typical) at VCC = 1.65 V
0.55 (typical) at VCC = 2.3 V
0.50 (typical) at VCC = 2.7 V
0.50 (typical) at VCC = 4.3 V
High noise immunity
ESD protection:
HBM JESD22-A114F Class 3A exceeds 7500 V
MM JESD22-A115-A exceeds 200 V
CDM AEC-Q100-011 revision B exceeds 1000 V
IEC61000-4-2 contact discharge exceeds 4000 V for switch ports
CMOS low-power consumption
Latch-up performance exceeds 100 mA per JESD 78 Class II Level A
Direct interface with TTL levels at 3.0 V
Control input accepts voltages above supply voltage
High current handling capability (350 mA continuous current under 3.3 V supply)
Specified from 40 C to +85 C and from 40 C to +125 C
3. Applications
Cell phone
PDA
Portable media player
1 page  
NXP Semiconductors
NX3L2G66
Dual low-ohmic single-pole single-throw analog switch
10. Recommended operating conditions
Table 6. Recommended operating conditions
Symbol Parameter
Conditions
VCC
VI
VSW
Tamb
t/V
supply voltage
input voltage
switch voltage
ambient temperature
input transition rise and fall rate
enable input nE
VCC = 1.4 V to 4.3 V
Min Typ Max Unit
1.4 -
4.3 V
0-
4.3 V
[1] 0
40
-
-
VCC
+125
V
C
[2] - - 200 ns/V
[1] To avoid sinking GND current from terminal nZ when switch current flows in terminal nY, the voltage drop across the bidirectional switch
must not exceed 0.4 V. If the switch current flows into terminal nZ, no GND current will flow from terminal nY. In this case, there is no
limit for the voltage drop across the switch.
[2] Applies to control signal levels.
11. Static characteristics
Table 7. Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground 0 V).
Symbol Parameter Conditions
Tamb = 25 C
Min Typ Max
Tamb = 40 C to +125 C Unit
Min Max Max
(85 C) (125 C)
VIH
VIL
II
IS(OFF)
IS(ON)
ICC
HIGH-level
input voltage
LOW-level
input voltage
input leakage
current
OFF-state
leakage
current
ON-state
leakage
current
supply current
VCC = 1.4 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
VCC = 1.4 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
enable input nE;
VI = GND to 4.3 V;
VCC = 1.4 V to 4.3 V
nY port; see Figure 6
VCC = 1.4 V to 3.6 V
VCC = 3.6 V to 4.3 V
nZ port; see Figure 7
VCC = 1.4 V to 3.6 V
VCC = 3.6 V to 4.3 V
VI = VCC or GND;
VSW = GND or VCC
VCC = 3.6 V
VCC = 4.3 V
0.65VCC
1.7
-
-
- 0.65VCC -
- 1.7 -
-V
-V
2.0 - - 2.0 -
-V
0.7VCC
-
-
- - 0.7VCC -
-V
- 0.35VCC - 0.35VCC 0.35VCC V
- 0.7 - 0.7 0.7 V
- - 0.8 - 0.8 0.8 V
- - 0.3VCC - 0.3VCC 0.3VCC V
---
- 0.5 1 A
- - 5 - 50 500 nA
- - 10 - 50 500 nA
- - 5 - 50 500 nA
- - 10 - 50 500 nA
- - 100 - 690 6000 nA
- - 150 - 800 7000 nA
NX3L2G66
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 7 February 2013
© NXP B.V. 2013. All rights reserved.
5 of 22
5 Page 
NXP Semiconductors
NX3L2G66
Dual low-ohmic single-pole single-throw analog switch
12.1 Waveform and test circuits
nE input
VI
GND
VOH
nY output
OFF to HIGH
HIGH to OFF
GND
VM
ten
switch
disabled
tdis
VX VX
switch
enabled
switch
disabled
001aah376
Measurement points are given in Table 10.
Logic level: VOH is the typical output voltage level that occurs with the output load.
Fig 16. Enable and disable times
Table 10. Measurement points
Supply voltage
VCC
1.4 V to 4.3 V
Input
VM
0.5VCC
Output
VX
0.9VOH
VCC
nE
nY/nZ
nZ/nY
G VI V VO
RL
CL
VEXT = 1.5 V
Test data is given in Table 11.
Definitions for test circuit:
RL = load resistance.
CL = load capacitance including jig and probe capacitance.
VEXT = external voltage for measuring switching times.
Fig 17. Test circuit for measuring switching times
Table 11. Test data
Supply voltage
VCC
1.4 V to 4.3 V
Input
VI
VCC
tr, tf
2.5 ns
001aaj224
Load
CL
35 pF
RL
50
NX3L2G66
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 7 February 2013
© NXP B.V. 2013. All rights reserved.
11 of 22
11 Page | ||
| Páginas | Total 22 Páginas | |
| PDF Descargar | [ Datasheet NX3L2G66.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| NX3L2G66 | Dual low-ohmic single-pole single-throw analog switch | NXP Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |