|
|
PDF IDTF1701NBGI Data sheet ( Hoja de datos )
| Número de pieza | IDTF1701NBGI | |
| Descripción | RF to IF Single Downconverting Mixer | |
| Fabricantes | Integrated Device Technology | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de IDTF1701NBGI (archivo pdf) en la parte inferior de esta página. Total 24 Páginas | ||
|
No Preview Available !
RF to IF Single Downconverting Mixer
GENERAL DESCRIPTION
This document describes the specification for the
IDTF1701 Zero-DistortionTM Lowband RF to IF Single
Downconverting Mixer. This device is part of a series of
mixers using lowside or highside LO injection options for
all UTRA frequency bands. See the Part# Matrix for the
detail of all devices in this series.
The F1701 single channel device is designed to operate
with a single 5V supply. It is optimized for operation in
a Multi-mode, Multi-carrier BaseStation Receiver over
the frequency range from 600MHz to 1060MHz using
either lowside or highside LO. IF frequencies from
70MHz to 300MHz are supported. Nominally, the
device offers +43dBm Output IP3 using HS LO with
184mA of ICC.
COMPETITIVE ADVANTAGE
In typical basestation receivers, the RF to IF mixer
dominates the linearity performance for the entire
receive system. The Zero-DistortionTM family of mixers
dramatically improve the maximum signal levels (IM3
tones) that the BTS can withstand at a desired Signal to
Noise Ratio (SNR.) Zero-DistortionTM technology allows
realization of either benefit. In basestation transmitters,
digital pre-distortion (DPD) is employed to improve the
Transmitter performance. By utilizing an ultra-linear
mixer in the DPD RX path, such as the IDTF1701, the
ACLR and/or power consumption of the full Tx system
can be improved significantly. This is because the F1701
can directly drive an ADC through an Anti-Alias filter.
Downstream amplification is not necessary in the DPD
application.
IP3O: 9 dB
Dissipation: 14%
Allows for higher RF gain
improving Sensitivity
Eliminates the need for an
ADC driver or IF VGA in DPD
linearization path
PART# MATRIX
Part#
F1701
F1751
F1763
RF Range
600 - 1060
1400 - 2500
2000 - 2900
UTRA bands
5,6,8,12,13,14,17,1
8,19,20, 26
1,2,3,4,9,10,11,
21,23,24,25,33,34,
35,36,37,39, 40
7,38,40,41
IF freq
range
70 - 300
50 - 500
50 - 500
Typ.
Gain
11.8
11.8
Injection
Both
Both
11.7
Both
IDTF1701NBGI
Datasheet
600MHz to 1060MHz
FEATURES
Ideal for Multi-Carrier Systems
Lowside or Highside LO
11.8dB Gain
Ultra linear +43dBm IP3O using HS LO or
+42dBm IP3O using LS LO
9.2dB NF
200 Ω output impedance
Wide flat performance IF BW
Drives ADC directly for DPD applications
Low Power Consumption
5x5 20 pin package
Standby Mode
DEVICE BLOCK DIAGRAM
RF
IFOUT
LO
Bias
STBY
Control
ISET
VCC
ORDERING INFORMATION
Omit IDT
prefix
0.8 mm height
package
IDTF1701NBGI8
Tape &
Reel
RF product Line
Green Industrial
Temp range
IDT Zero-DistortionTM Mixer
1
RevO December 2013
1 page  
RF to IF Single Downconverting Mixer
IDTF1701NBGI
Datasheet
600MHz to 1060MHz
IDTF1701 SPECIFICATION - CONTINUED
Refer to Typical Application Circuit when operated with VCC = +5.0V, TC= +25°C, FRF = 950 MHz, FIF = 200 MHz, FLO = 1150 MHz, PLO = 0
dBm, output power = +1dBm per tone, STBY = GND unless otherwise noted. Transformer loss is de-embedded unless otherwise noted.
IM2 Sum Product (IM2+)
Pout = -3 dBm each tone
FIF1 = 200 MHz, FIF2 = 205 MHz
IM2 Product = 405 MHz
IM2+
-75 -69 dBc
IM2 Diff Product (IM2-)
Pout = -3 dBm each tone
FIF1 = 200 MHz, FIF2 = 205 MHz
IM2 Product = 5 MHz
IM2-
-80 -75 dBc
1dB output compression Output referred
P1dBO
17
21
dBm
1dB input compression
Gain Comp. w/blocker
Gain Ripple
Input referred
Unmodulated blocker
Pin = -4 dBm, -100MHz offset
Signal Pin Tone = -20dBm
Measure Δ gain of signal
Fixed LO = 1100 MHz
RF = 770 to 1050 MHz
IF = 50 to 330 MHz
P1dBI
ΔGAC
10.2 dBm
0.1 0.15
dB
1 1.2 dB
RF Input Impedance
Single Ended
ZRF
50
LO port Impedance
Single Ended
ZLO
50
Ω
IF Output Impedance
Differential
ZIF 200
RF Input Return Loss
Single Ended
RFRL
14
20
dB
LO port Return Loss
Single Ended
LORL
18
22
dB
IF Output Return Loss
LO to IF leakage2
Differential
IFRL 17 19
dB
ISOLI
-55 -39 dBm
RF to IF leakage
Referenced to Pin = -10dBm
ISORI
-41 -34 dBc
LO to RF leakage
ISOLR
-43.5
-38
dBm
1 – Items in min/max columns in bold italics are Guaranteed by Test
2 – All other Items in min/max columns are Guaranteed by Design Characterization
IDT Zero-DistortionTM Mixer
5
RevO December 2013
5 Page 
IDTF1701NBGI
Datasheet
RF to IF Single Downconverting Mixer
600MHz to 1060MHz
TOCS [IF = 200MHZ, HIGH SIDE INJECTION] RF to IF leakage, OIP3, HD2 (5)
RF to IF leakage vs. TCASE
0
-6
-12
-18
-24
-30
-36
-42
-48
-54
-60
650
105degC - +5.0V - 0dBm 25degC - +5.0V - 0dBm -40degC - +5.0V - 0dBm
750 850 950 1050
RF Frequency (MHz)
RF to IF leakage vs. Vcc
0
-6
-12
-18
-24
-30
-36
-42
-48
-54
-60
650
25degC - +4.75V - 0dBm 25degC - +5.0V - 0dBm 25degC - +5.25V - 0dBm
750 850 950 1050
RF Frequency (MHz)
HD2 vs. Input power
0
-10
-20 25degC - +5.0V - 0dBm - 650MHz
25degC - +5.0V - 0dBm - 950MHz
-30
-40
-50
-60
-70
-80
-90
-100
-20 -18 -16 -14 -12 -10 -8 -6
25degC - +5.0V - 0dBm - 800MHz
25degC - +5.0V - 0dBm - 1100MHz
-4 -2 0 2 4 6 8
10
Input Power (dBm)
RF to IF leakage vs. Lo Level
0
-6
-12
-18
-24
-30
-36
-42
-48
-54
-60
650
25degC - +5.0V - 0dBm 25degC - +5.0V - 3dBm 25degC - +5.0V - -3dBm
750 850
RF Frequency (MHz)
950
1050
OIP3 vs. Input power
50
45
40
35
30
25
20
15 25degC - +5.0V - 0dBm - 650MHz
10 25degC - +5.0V - 0dBm - 950MHz
5
0
-20 -18 -16 -14 -12 -10 -8 -6
25degC - +5.0V - 0dBm - 800MHz
25degC - +5.0V - 0dBm - 1100MHz
-4 -2 0 2 4 6 8
10
Input Power (dBm)
OIP3 vs. Delta Frequency of two tones
50
45
40
35
30
25
20
15 25degC - +5.0V - 0dBm - 650MHz 25degC - +5.0V - 0dBm - 800MHz
10 25degC - +5.0V - 0dBm - 950MHz 25degC - +5.0V - 0dBm - 1100MHz
5
0
0.8 2.8 4.8 6.8 8.8 10.8 12.8 14.8 16.8 18.8 20.8 22.8 24.8 26.8 28.8 30.8
Two tones Delta Frequency (MHz)
IDT Zero-DistortionTM Mixer
11
RevO December 2013
11 Page | ||
| Páginas | Total 24 Páginas | |
| PDF Descargar | [ Datasheet IDTF1701NBGI.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| IDTF1701NBGI | RF to IF Single Downconverting Mixer | Integrated Device Technology |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |