|
|
Número de pieza | NTDV20N06 | |
Descripción | Power MOSFET ( Transistor ) | |
Fabricantes | ON Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de NTDV20N06 (archivo pdf) en la parte inferior de esta página. Total 7 Páginas | ||
No Preview Available ! NTD20N06, NTDV20N06
Power MOSFET
20 A, 60 V, N−Channel DPAK
Designed for low voltage, high speed switching applications in power
supplies, converters and power motor controls and bridge circuits.
Features
• Lower RDS(on)
• Lower VDS(on)
• Lower Capacitances
• Lower Total Gate Charge
• Lower and Tighter VSD
• Lower Diode Reverse Recovery Time
• Lower Reverse Recovery Stored Charge
• AEC Q101 Qualified − NTDV20N06
• These Devices are Pb−Free and are RoHS Compliant
Typical Applications
• Power Supplies
• Converters
• Power Motor Controls
• Bridge Circuits
MAXIMUM RATINGS (TJ = 25°C unless otherwise noted)
Rating
Symbol Value Unit
Drain−to−Source Voltage
Drain−to−Gate Voltage (RGS = 10 MW)
Gate−to−Source Voltage
− Continuous
− Non−repetitive (tpv10 ms)
Drain Current
− Continuous @ TA = 25°C
− Continuous @ TA = 100°C
− Single Pulse (tpv10 ms)
Total Power Dissipation @ TA = 25°C
Derate above 25°C
Total Power Dissipation @ TA = 25°C (Note 1)
Total Power Dissipation @ TA = 25°C (Note 2)
Operating and Storage Temperature Range
VDSS
VDGR
VGS
VGS
ID
ID
IDM
PD
TJ, Tstg
60
60
±20
±30
20
10
60
60
0.40
1.88
1.36
−55 to
175
Vdc
Vdc
Vdc
Adc
Apk
W
W/°C
W
W
°C
Single Pulse Drain−to−Source Avalanche
Energy − Starting TJ = 25°C
(VDD = 25 Vdc, VGS = 10 Vdc,
L = 1.0 mH, IL(pk) = 18.4 A, VDS = 60 Vdc)
Thermal Resistance
− Junction−to−Case
− Junction−to−Ambient (Note 1)
− Junction−to−Ambient (Note 2)
Maximum Lead Temperature for Soldering
Purposes, 1/8″ from case for 10 seconds
EAS
RqJC
RqJA
RqJA
TL
170 mJ
°C/W
2.5
80
110
260 °C
Stresses exceeding those listed in the Maximum Ratings table may damage the
device. If any of these limits are exceeded, device functionality should not be
assumed, damage may occur and reliability may be affected.
1. When surface mounted to an FR4 board using the minimum recommended
pad size.
2. When surface mounted to an FR4 board using the 0.5 sq in drain pad size.
http://onsemi.com
V(BR)DSS
60 V
RDS(on) TYP
37.5 mW
ID MAX
20 A
N−Channel
D
G
S
4
12
3
DPAK
CASE 369C
STYLE 2
MARKING DIAGRAM
& PIN ASSIGNMENTS
4
Drain
1
Gate
2
Drain
3
Source
A
20N06
Y
WW
G
= Assembly Location*
= Device Code
= Year
= Work Week
= Pb−Free Package
* The Assembly Location code (A) is front side
optional. In cases where the Assembly Location is
stamped in the package, the front side assembly
code may be blank.
ORDERING INFORMATION
See detailed ordering and shipping information on page 2 of
this data sheet.
© Semiconductor Components Industries, LLC, 2014
September, 2014 − Rev. 9
1
Publication Order Number:
NTD20N06/D
1 page NTD20N06, NTDV20N06
12
10 QT
8
6 Q1
Q2
VGS
4
2
0
04
ID = 20 A
TJ = 25°C
8 12 16 20 24
QG, TOTAL GATE CHARGE (nC)
Figure 8. Gate−To−Source and Drain−To−Source
Voltage versus Total Charge
1000
VDS = 30 V
ID = 20 A
VGS = 10 V
100
tr
td(off)
10
td(on)
tf
1
1 10
RG, GATE RESISTANCE (OHMS)
Figure 9. Resistive Switching Time
Variation versus Gate Resistance
DRAIN−TO−SOURCE DIODE CHARACTERISTICS
20
VGS = 0 V
16 TJ = 25°C
100
12
8
4
0
0.6 0.7 0.8 0.9
VSD, SOURCE−TO−DRAIN VOLTAGE (VOLTS)
1
Figure 10. Diode Forward Voltage versus Current
SAFE OPERATING AREA
The Forward Biased Safe Operating Area curves define
the maximum simultaneous drain−to−source voltage and
drain current that a transistor can handle safely when it is
forward biased. Curves are based upon maximum peak
junction temperature and a case temperature (TC) of 25°C.
Peak repetitive pulsed power limits are determined by using
the thermal response data in conjunction with the procedures
discussed in AN569, “Transient Thermal Resistance −
General Data and Its Use.”
Switching between the off−state and the on−state may
traverse any load line provided neither rated peak current
(IDM) nor rated voltage (VDSS) is exceeded and the
transition time (tr,tf) do not exceed 10 ms. In addition the total
power averaged over a complete switching cycle must not
exceed (TJ(MAX) − TC)/(RqJC).
A Power MOSFET designated E−FET can be safely used
in switching circuits with unclamped inductive loads. For
reliable operation, the stored energy from circuit inductance
dissipated in the transistor while in avalanche must be less
than the rated limit and adjusted for operating conditions
differing from those specified. Although industry practice is
to rate in terms of energy, avalanche energy capability is not
a constant. The energy rating decreases non−linearly with an
increase of peak current in avalanche and peak junction
temperature.
Although many E−FETs can withstand the stress of
drain−to−source avalanche at currents up to rated pulsed
current (IDM), the energy rating is specified at rated
continuous current (ID), in accordance with industry custom.
The energy rating must be derated for temperature as shown
in the accompanying graph (Figure 12). Maximum energy at
currents below rated continuous ID can safely be assumed to
equal the values indicated.
http://onsemi.com
5
5 Page |
Páginas | Total 7 Páginas | |
PDF Descargar | [ Datasheet NTDV20N06.PDF ] |
Número de pieza | Descripción | Fabricantes |
NTDV20N06 | Power MOSFET ( Transistor ) | ON Semiconductor |
NTDV20N06L | Power MOSFET ( Transistor ) | ON Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |