CAT25M01 Datasheet PDF - ON Semiconductor
| Part Number | CAT25M01 | |
| Description | 1Mb SPI Serial CMOS EEPROM | |
| Manufacturers | ON Semiconductor | |
| Logo |  |
|
|
There is a preview and CAT25M01 download ( pdf file ) link at the bottom of this page. Total 14 Pages | ||
Preview 1 page No Preview Available !
CAT25M01
1 Mb SPI Serial CMOS
EEPROM
Description
The CAT25M01 is a 1M−bit Serial CMOS EEPROM device
internally organized as 128Kx8 bits. This features a 256−byte page
write buffer and supports the Serial Peripheral Interface (SPI)
protocol. The device is enabled through a Chip Select (CS) input. In
addition, the required bus signals are clock input (SCK), data input
(SI) and data output (SO) lines. The HOLD input may be used to pause
any serial communication with the CAT25M01 device. The device
features software and hardware write protection, including partial as
well as full array protection.
On−Chip ECC (Error Correction Code) makes the device suitable
for high reliability applications.
Features
• 10 MHz SPI Compatible
• 1.8 V to 5.5 V Supply Voltage Range
• SPI Modes (0,0) & (1,1)
• 256−byte Page Write Buffer
• Additional Identification Page with Permanent Write Protection
• Self−timed Write Cycle
• Hardware and Software Protection
• Block Write Protection –
Protect 1/4, 1/2 or Entire EEPROM Array
• Low Power CMOS Technology
• 1,000,000 Program/Erase Cycles
• 100 Year Data Retention
• Industrial and Extended Temperature Range
• 8 lead SOIC and TSSOP Packages
• This Device is Pb−Free, Halogen Free/BFR Free and is RoHS
Compliant
VCC
SI
CS
WP
HOLD
SCK
CAT25M01
SO
VSS
Figure 1. Functional Symbol
www.onsemi.com
TSSOP−8
Y SUFFIX
CASE 948AL
SOIC−8
V SUFFIX
CASE 751BD
SOIC−8
X SUFFIX
CASE 751BE
PIN CONFIGURATION
CS 1
SO
WP
VSS
VCC
HOLD
SCK
SI
SOIC (V, X),
TSSOP (Y)
(Top View)
Pin Name
CS
SO
WP
VSS
SI
SCK
HOLD
VCC
PIN FUNCTION
Function
Chip Select
Serial Data Output
Write Protect
Ground
Serial Data Input
Serial Clock
Hold Transmission Input
Power Supply
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 14 of this data sheet.
© Semiconductor Components Industries, LLC, 2016
October, 2016 − Rev. 2
1
Publication Order Number:
CAT25M01/D
|
| |
 
CAT25M01
Status Register
The Status Register, as shown in Table 8, contains a
number of status and control bits.
The RDY (Ready) bit indicates whether the device is busy
with a write operation. This bit is automatically set to 1
during an internal write cycle, and reset to 0 when the device
is ready to accept commands. For the host, this bit is read
only.
The WEL (Write Enable Latch) bit is set/reset by the
WREN/WRDI commands. When set to 1, the device is in a
Write Enable state and when set to 0, the device is in a Write
Disable state.
The BP0 and BP1 (Block Protect) bits determine which
blocks are currently write protected. They are set by the user
with the WRSR command and are non−volatile. The user is
allowed to protect a quarter, one half or the entire memory,
by setting these bits according to Table 9. The protected
blocks then become read−only.
The WPEN (Write Protect Enable) bit acts as an enable for
the WP pin. Hardware write protection is enabled when the
WP pin is low and the WPEN bit is 1. This condition
Table 8. STATUS REGISTER
76
WPEN
IPL
5
0
4
LIP
prevents writing to the status register and to the block
protected sections of memory. While hardware write
protection is active, only the non−block protected memory
can be written. Hardware write protection is disabled when
the WP pin is high or the WPEN bit is 0. The WPEN bit, WP
pin and WEL bit combine to either permit or inhibit Write
operations, as detailed in Table 10.
The IPL (Identification Page Latch) bit determines
whether the additional Identification Page (IPL = 1) or main
memory array (IPL = 0) can be accessed both for Read and
Write operations. The IPL bit is set by the user with the
WRSR command and is volatile. The IPL bit is
automatically reset after read/write operations.
The LIP bit is set by the user with the WRSR command
and is non−volatile. When set to 1, the Identification Page is
permanently write protected (locked in Read−only mode).
Note: The IPL and LIP bits cannot be set to 1 using the
same WRSR instruction. If the user attempts to set (“1”)
both the IPL and LIP bit in the same time, these bits cannot
be written and therefore they will remain unchanged.
3210
BP1
BP0
WEL
RDY
Table 9. BLOCK PROTECTION BITS
Status Register Bits
BP1 BP0
00
01
10
11
Array Address Protected
None
18000h−1FFFFh
10000h−1FFFFh
00000h−1FFFFh
Protection
No Protection
Quarter Array Protection
Half Array Protection
Full Array Protection
Table 10. WRITE PROTECT CONDITIONS
WPEN
WP
WEL
0X0
0X1
1 Low 0
1 Low 1
X High 0
X High 1
Protected Blocks
Protected
Protected
Protected
Protected
Protected
Protected
Unprotected Blocks
Protected
Writable
Protected
Writable
Protected
Writable
Status Register
Protected
Writable
Protected
Protected
Protected
Writable
www.onsemi.com
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for CAT25M01 electronic component. |
| Information | Total 14 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ CAT25M01.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| CAT25M01 | The function is 1Mb SPI Serial CMOS EEPROM. ON Semiconductor | |
| CAT25M02 | The function is 2Mb SPI Serial CMOS EEPROM. ON Semiconductor | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
CAT2
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||