DataSheetWiki


PD69100 fiches techniques PDF

Microsemi - PoE Controller Unit

Numéro de référence PD69100
Description PoE Controller Unit
Fabricant Microsemi 
Logo Microsemi 





1 Page

No Preview Available !





PD69100 fiche technique
®
TM
DESCRIPTION
Microsemi’s™ PoE controller, PD69100, is a cost-
effective, pre-programmed unit designed to implement
Enhanced mode. It is used in conjunction with Microsemi’s
PoE Managers PD69108 and PD69104 in Ethernet
switches to enable next generation network devices to
share power and data over the same cable, as specified in
IEEE802.3af and IEEE802.3at standards. Enhanced
mode operation along with PD69108/PD69104 managers
enables operation in a total Power-over-Ethernet stand-
alone mode.
The controller features an ESPI bus for each PoE device
and a communication interface with Host CPU via UART
or I2C protocol.
Device is based on STMicroelectronics family
STM32F101T6 embedded with ARM Cortex™-M3 core. It
includes the following peripherals:
3 x Timers
2 x Uarts
1 x SPI
1 x I2C
1 x 12-bit analog-to-digital converter
PIN CONFIGURATION
27 26 25 24 23 22 21 20 19
SWCLK 28
xDisable_Ports 29
xHswp_On 30
Spare 31
xSys_OK 32
SCL / UART1_TX 33
SDA / UART1_RX 34
Boot0 35
VSS3 36
<Part Number >
< -Software Ver >
< Date Code >
12 3 4 5 6 7 8 9
18 VSS1
17 Reserved
16 I2C_ADDR
15 HW_VER
14 ESPI_MOSI
13 ESPI_MISO
12 ESPI_SCK
11 ESPI_xCS
10 Reserved
PD69100
PoE Controller Unit
DATASHEET
KEY FEATURES
Controls up to 48 PoE ports (6 x PD69108)
Pre-Standard / Capacitor detection
Detection of Cisco devices
Supports both UART and I2C interfaces to
Host CPU
Backwards compatible with PD69000,
PD63000, PD62000 and PDIC66000
Supports 2 pair RJ or 4 pair RJ
16 power banks support using four discrete
lines connected directly to PD69108 /
PD69104.
Power management for up to 96 ports
Rmode pin for default parameters selection
Programmable over-voltage and under voltage
Predefined power budget; 16 discrete levels
LED stream support
System OK indication
Software download via I2C or UART
System and port measurements
Detailed port status
Thermal protection and monitoring
Programmable temperature alarm limit
Interrupt out pin for system and port events
Forced power for system testing
System reset
Port power limit setting
Port matrix and priority
Automatic PoE device type detection
RoHS compliant
MARKETING DEFINITIONS
Device’s label includes the following:
<Part number> Hardware P/N (for example
PD69100)
<-Software Ver> Software version (for
example. 0120)
<Date Code> Burning date code in the
following format: yyww (yy = year, ww = week)
FIRMWARE DOWNLOAD
Initial burning of controller's firmware is
performed in factory. Firmware upgrades can
be performed by users using communication
interface (see application note 126 catalogue
number 06-0006-080).
ORDERING INFORMATION
Part Number PD69100y-gggg
Detection
y = R: Resistor
y = C: Resistor/legacy
Version
gggg
*For latest firmware version available, refer to Microsemi's website or Customer Care Support.
Copyright © 2010
Microsemi
Rev. 1.1, Dec. 2010
Analog Mixed Signal Group
2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308
1

PagesPages 5
Télécharger [ PD69100 ]


Fiche technique recommandé

No Description détaillée Fabricant
PD69100 PoE Controller Unit Microsemi
Microsemi

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche