DataSheetWiki


NTCALUG01A fiches techniques PDF

Vishay - Standard Lug Sensors

Numéro de référence NTCALUG01A
Description Standard Lug Sensors
Fabricant Vishay 
Logo Vishay 





1 Page

No Preview Available !





NTCALUG01A fiche technique
www.vishay.com
NTCALUG01A Series
Vishay BCcomponents
NTC Thermistors, Standard Lug Sensors
QUICK REFERENCE DATA
PARAMETER
VALUE
UNIT
Resistance value at 25 °C (2)
4.7K to 100K
Tolerance on R25-value (2)
B25/85-value
Tolerance on B25/85-value
Operating temperature range at:
± 2, ± 3, ± 5
3984 to 4190
± 0.5 to ± 1.5
%
K
%
Zero dissipation
- 40 to + 150
°C
Maximum dissipation
0 to + 55
Dissipation factor (3)
23 mW/K
Thermal time constant (3)
7.5
s
Min. dielectric withstanding
voltage between terminals and lug
1500 (1 s)
VAC
Insulation resistance between
terminals and lug at 500 VDC
Climatic category (LCT/UCT/days)
min. 100
40/150/56
M
Weight
1.6 g
Notes
(2) Other R25-values and tolerances are available upon request
(3) Measured with screw mounted on an aluminium heatsink of
100 cm2, thickness 1.5 mm, in still air at Tamb = + 25 °C
PACKAGING
The thermistors are packed in cardboard boxes; the
smallest packaging quantity is 500 units.
MOUNTING
• By means of M3 screw. Leads to be soldered or crimped
• The device is suitable for screwing e.g. on metal surface
• The leads are suitable for soldering e.g. on PCB
• Other screw sizes are available on request
FEATURES
• Easy mounting using ring tongue terminal
• Rugged construction
• Cable of PTFE insulation acoording to
NEMA HP-3, type E, rated 600 VRMS (1)
• AEC-Q200 qualified (grade 1)
• Material categorization:
For definitions of compliance please see
www.vishay.com/doc?99912
Note
(1) Formerly MIL-W-16878/4, type E
APPLICATIONS
• Suitable for surface sensing applications, especially when
a good electrical insulation and a good thermal contact
with the chassis is required.
• Thermistor with negative temperature coefficient and two
stranded PTFE insulated copper leads.
• The device is mounted inside the barrel of the ring tongue
terminal.
DIMENSIONS
Dia hole D1
D2
L2
L1
L3 max.
T
90169 a
L1 = 38.1 mm ± 3.8 mm
L2 = 3.81 mm ± 0.64 mm
For info: D1 = 3.68 mm, D2 = 7.14 mm, L3 = 16.26 mm, T = 1.016 mm
Notes
• The thermistor chip NTC is epoxy coated and attached to the
metal lug via a middle buffer layer
• Metal ring lug is tinned copper
• Insulated leads: AWG # 24 stranded, PTFE insulation,
Ø 1.12 mm
• Lead wire end twisted and tinned, other lead length and
insulation, available on request
DESIGNERS TOOL
• Other resistance curves and tolerances are available on
request
• Consult Vishay for other lead length, other connector
crimping or other features
• 3D solid models: www.vishay.com/doc?29106
• NTC curve computation:
www.vishay.com/resistors-non-linear/curve-computation-list/
Revision: 08-Aug-12
1 Document Number: 29092
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

PagesPages 3
Télécharger [ NTCALUG01A ]


Fiche technique recommandé

No Description détaillée Fabricant
NTCALUG01A Standard Lug Sensors Vishay
Vishay
NTCALUG01A103G Standard Lug Sensors Vishay
Vishay
NTCALUG01A103H Standard Lug Sensors Vishay
Vishay
NTCALUG01A103J Standard Lug Sensors Vishay
Vishay

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche