DataSheetWiki


R5478N110CD fiches techniques PDF

RICOH - Li-ION/POLYMER 1CELL PROTECTOR

Numéro de référence R5478N110CD
Description Li-ION/POLYMER 1CELL PROTECTOR
Fabricant RICOH 
Logo RICOH 





1 Page

No Preview Available !





R5478N110CD fiche technique
Li-ION/POLYMER 1CELL PROTECTOR
R5475N/R5478N SERIES
No. EA-291-121009
OUTLINE
The R5475N/R5478Nxxxxx Series are high voltage CMOS-based protection ICs for over-charge/discharge of
rechargeable one-cell Lithium-ion (Li+) / Lithium polymer excess load current, further include a short circuit
protector for preventing large external short circuit current and Excess discharge-current.
Each of these ICs is composed of three voltage detectors, a reference unit, a delay circuit, a short circuit
protector, an oscillator, a counter, and a logic circuit. When the over-charge voltage crosses the detector
threshold from a low value to a high value, the output of COUT pin switches to low level after internal fixed delay
time. The conditions to release over-charge detector are different by mask options. In terms of so called “Latch
function” version, after detecting over-charge, the detector can be reset and the output of COUT becomes "H"
when a kind of load is connected to VDD after a charger is disconnected from the battery pack, and the cell
voltage becomes lower than over-charge detector threshold. If a charger is continue to be connected to the
battery pack, even the cell voltage becomes lower than over-charge detector threshold, over-charge state is not
released. On the other hand, in terms of so called, “ Released by voltage level” version, after detecting
over-charge, when the cell voltage reaches the released voltage from over-charge, the output of COUT becomes
“H”
The output of DOUT pin, the output of Over-discharge detector and Excess discharge-current detector,
switches to “L” level after internally fixed delay time, when discharged voltage crosses the detector threshold
from a high value to a value lower than VDET2.
The conditions to release over-discharge detector are also different by mask options. In terms of so called
“Latch function” version, after detecting over-discharge voltage, connect a charger to the battery pack, and
when the battery supply voltage becomes higher than over-discharge detector threshold, VD2 is released and
the voltage of DOUT pin becomes "H" level. On the other hand, in terms of so called “Released by voltage level”
version, in case that the charger is not connected, when the cell voltage becomes equal released voltage from
over-discharge, over-discharge detector is released. In case that a charger is connected, and when the cell
voltage becomes the released voltage from over-discharge, the over-discharge detector is released.
An excess discharge-current and short circuit state can be sensed and cut off through the built in excess
current detector, VD3, with DOUT being enabled to low level. Once after detecting excess discharge-current or
short circuit, the VD3 is released and DOUT level switches to high by detaching a battery pack from a load
system.
After detecting over-discharge, supply current will be kept extremely low by halting internal circuits' op-
eration.
When the output of COUT is “H”, if V- pin level is set at Vss-2V, the delay time of detector can be shortened.
Especially, the delay time of over-charge detector can be reduced into approximately 1/57. Therefore, testing
time of protector circuit board can be reduced. Output type of COUT and DOUT are CMOS. 6-pin, SOT-23-6 is
available.
-1-

PagesPages 27
Télécharger [ R5478N110CD ]


Fiche technique recommandé

No Description détaillée Fabricant
R5478N110CD Li-ION/POLYMER 1CELL PROTECTOR RICOH
RICOH

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche