DataSheetWiki


HWD810 fiches techniques PDF

Chengdu Sino Microelectronics System - 3-Pin Microprocessor Reset Circuits

Numéro de référence HWD810
Description 3-Pin Microprocessor Reset Circuits
Fabricant Chengdu Sino Microelectronics System 
Logo Chengdu Sino Microelectronics System 





1 Page

No Preview Available !





HWD810 fiche technique
3-Pin Microprocessor Reset Circuits
General Description
The HWD803/HWD809/HWD810 are microprocessor (µP)
supervisory circuits used to monitor the power supplies
in µP and digital systems. They provide excellent circuit
reliability and low cost by eliminating external compo-
nents and adjustments when used with +5V, +3.3V,
+3.0V, or +2.5V powered circuits.
These circuits perform a single function: they assert a
reset signal whenever the VCC supply voltage declines
below a preset threshold, keeping it asserted for at
least 140ms after VCC has risen above the reset thresh-
old. Reset thresholds suitable for operation with a vari-
ety of supply voltages are available.
The HWD803 has an open-drain output stage, while the
HWD809/HWD810 have push-pull outputs. The
HWD803’s open-drain RESET output requires a pull-up
resistor that can be connected to a voltage higher than
VCC. The HWD803/HWD809 have an active-low RESET
output, while the HWD810 has an active-high RESET
output. The reset comparator is designed to ignore fast
transients on VCC, and the outputs are guaranteed to
be in the correct logic state for VCC down to 1V.
Low supply current makes the HWD803/HWD809/
HWD810 ideal for use in portable equipment. The
HWD803 is available in a 3-pin SC70 package, and the
HWD809/HWD810 are available in 3-pin SC70 or SOT23
packages.
Applications
Computers
Controllers
Intelligent Instruments
Critical µP and µC Power Monitoring
Portable/Battery-Powered Equipment
Automotive
Typical Operating Circuit
VCC
VCC
HWD803
HWD809
RESET
RPULL-UP*
VCC
µP
RESET
INPUT
GND GND
*HWD803 ONLY
____________________________Features
o Precision Monitoring of +2.5V, +3V, +3.3V, and
+5V Power-Supply Voltages
o Fully Specified Over Temperature
o Available in Three Output Configurations
Open-Drain RESET Output (HWD803)
Push-Pull RESET Output (HWD809)
Push-Pull RESET Output (HWD810)
o 140ms min Power-On Reset Pulse Width
o 12µA Supply Current
o Guaranteed Reset Valid to VCC = +1V
o Power Supply Transient Immunity
o No External Components
o 3-Pin SC70 and SOT23 Packages
Ordering Information
PART
TEMP. RANGE PIN-PACKAGE
HWD803_EXR-T
-40°C to +125°C 3 SC70-3
HWD803_EXR-T10 -40°C to +125°C 3 SC70-3
HWD809_EXR-T
-40°C to +125°C 3 SC70-3
HWD809_EXR-T10 -40°C to +125°C 3 SC70-3
HWD809_EUR-T
-40°C to +105°C 3 SOT23-3
HWD809_EUR-T10 -40°C to +105°C 3 SOT23-3
HWD810_EXR-T
-40°C to +125°C 3 SC70-3
HWD810_EXR-T10 -40°C to +125°C 3 SC70-3
HWD810_EUR-T
-40°C to +105°C 3 SOT23-3
HWD810_EUR-T10 -40°C to +105°C 3 SOT23-3
Note: These parts are offered in 2.5k or 10k reels, and must be
ordered in 2.5k or 10k increments. Order HWD803_EXR-T for
2.5k reels and HWD803_EXR-T10 for 10k reels. Insert the
desired suffix letter from the Selector Guide into the blank to
complete the part number. All versions of these products may
not be available at the time of announcement. Contact factory for
availability.
Pin Configuration
TOP VIEW
GND 1
HWD803
HWD809
HWD810
3 VCC
RESET (RESET) 2
( ) ARE FOR HWD810.
SC70-3/SOT23-3
HWD803 AVAILABLE IN SC70-3 ONLY.
1

PagesPages 9
Télécharger [ HWD810 ]


Fiche technique recommandé

No Description détaillée Fabricant
HWD810 3-Pin Microprocessor Reset Circuits Chengdu Sino Microelectronics System
Chengdu Sino Microelectronics System

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche