|
|
PDF ILX554B Data sheet ( Hoja de datos )
| Número de pieza | ILX554B | |
| Descripción | 2048-pixel CCD Linear Sensor | |
| Fabricantes | Sony | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ILX554B (archivo pdf) en la parte inferior de esta página. Total 13 Páginas | ||
|
No Preview Available !
ILX554B
2048-pixel CCD Linear Sensor (B/W) for Single 5V Power Supply Bar-code Reader
Description
The ILX554B is a rectangular reduction type CCD
linear image sensor designed for bar code POS
hand scanner and optical measuring equipment use.
A built-in timing generator and clock-drivers ensure
single 5V power supply for easy use.
22 pin DIP (Cer-DIP)
Features
• Number of effective pixels: 2048 pixels
• Pixel size:
14µm × 56µm
(14µm pitch)
• Single 5V power supply
• Ultra-high sensitivity
• Built-in timing generator and clock-drivers
• Built-in sample-and-hold circuit
• Maximum clock frequency: 2MHz
Block Diagram
Absolute Maximum Ratings
• Supply voltage
VDD
• Operating temperature
• Storage temperature
6
–10 to +60
–30 to +80
V
°C
°C
Pin Configuration (Top View)
VOUT 1
NC 2
NC 3
SHSW 4
φCLK 5
NC 6
NC 7
NC 8
NC 9
NC 10
φROG 11
1
2048
22 NC
21 NC
20 VDD
19 GND
18 NC
17 NC
16 NC
15 NC
14 NC
13 NC
12 NC
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
–1–
E01752A22-PS
1 page  
ILX554B
–5–
5 Page 
ILX554B
Notes on Handling
1) Static charge prevention
CCD image sensors are easily damaged by static discharge. Before handling, be sure to take the following
protective measures.
a) Either handle bare handed or use non-chargeable gloves, clothes or material. Also use conductive
shoes.
b) When handling directly use an eath band.
c) Install a conductive mat on the floor or working table to prevent the generation of static electricity.
d) lonized air is recommended for discharge when handling CCD image sensors.
e) For the shipment of mounted substrates use cartons treated for the prevention of static charges.
2) Notes on handling CCD Cer-DIP package
The following points should be observed when handling and installing this package.
a) (1) Compressive strength: 39N/surface
(Do not apply any load more than 0.7mm inside the outer perimeter of the glass portion.)
(2) Shearing strength: 29N/surface
(3) Tensile strength:
29N/surface
(4) Torsional strength: 0.9Nm
Upper ceramic layer 39N
29N
29N
0.9Nm
Low-melting glass
Lower ceramic layer (1)
(2)
(3)
(4)
b) In addition, if a load is applied to the entire surface by a hard component, bending stress may be
generated and the package may fracture, etc., depending on the flatness of the ceramic portion.
Therefore, for installation, either use an elastic load, such as a spring plate, or an adhesive.
c) Be aware that any of the following can cause the glass to crack because the upper and lower ceramic
layers are shielded by low-melting glass.
(1) Applying repetitive bending stress to the external leads.
(2) Applying heat to the external leads for an extended period of time with a soldering iron.
(3) Rapid cooling or heating.
(4) Applying a load or impact to a limited portion of the low-melting glass with a small-tipped tool such
as tweezers.
(5) Prying the upper or lower ceramic layers away at a support point of the low-melting glass.
Note that the preceding notes should also be observed when removing a component from a board after
it has already been soldered.
3) Soldering
a) Make sure the package temperature does not exceed 80°C.
b) Solder dipping in a mounting furnace causes demage to the glass abd other defects. Use a grounded
30W soldering iron and solder each pin in less than 2 seconds. For repairs and remount, cool
sufficiently.
c) To dismount image sensors, do not use a solder suction equipment. When using an electric desoldering
tool, ground the controller. For the control system, use a zero cross type.
– 11 –
11 Page | ||
| Páginas | Total 13 Páginas | |
| PDF Descargar | [ Datasheet ILX554B.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ILX554 | 2048-pixel CCD Linear Sensor (B/W) for Single 5V Power Supply Bar-code Reader |  Sony Corporation |
| ILX554A | 2048-pixel CCD Linear Sensor (B/W) for Single 5V Power Supply Bar-code Reader | Sony Corporation |
| ILX554B | 2048-pixel CCD Linear Sensor | Sony |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |