DataSheetWiki


RET012864Q fiches techniques PDF

Raystar - OLED Graphic 128x64 dots Display

Numéro de référence RET012864Q
Description OLED Graphic 128x64 dots Display
Fabricant Raystar 
Logo Raystar 





1 Page

No Preview Available !





RET012864Q fiche technique
Your Best Partner of the Display Solutions
OLED Graphic
type
Mechanical Data
Item Dimension
Module dimension
73.0 × 41.86 × 3.0
View area
63.41 × 32.69
Active area
61.41 × 30.69
Dot Size
0.45 × 0.45
Dot Pitch
0.48 × 0.48
Absolute Maximum Rating
Unit
mm
mm
mm
mm
mm
Parameter
Symbol Min Max Unit Notes
Supply Voltage for Logic VDD -0.3
4
V 1, 2
Supply Voltage for Display VCC 0 16 V 1, 2
Electronical Characteristics
Symbol
Parameter
Test Condition
Min Typ Max Unit
VCC Operating Voltage - 8 12 16 V
VDD Logic Supply Voltage - 2.4 2.7 3.5 V
VOH High Logic Output Level IOUT = 100uA, 3.3MHz 0.9*VDD -
VDD V
VOL Low Logic Output Level IOUT = 100uA, 3.3MHz
0
- 0.1*VDD V
VIH High Logic Input Level IOUT = 100uA, 3.3MHz 0.8*VDD -
VDD V
VIL Low Logic Input Level IOUT = 100uA, 3.3MHz 0
- 0.2*VDD V
ISLEEP Sleep mode Current
No loading
- 0.2 5 uA
VCC Supply Current
ICC
VDD=2.7V, external VCC=12V,
IREF=10uA, Frame rate=110Hz, All one
pattern, Display on, no loading
VDD Supply Current
IDD
VDD=2.7V, external VCC=12V,
IREF=10uA, Frame rate=110Hz, All one
pattern, Display on, no loading
Contrast = 7F
Contrast = 7F
- 700 - uA
- - 650 uA
ISEG
Segment Output Current
VDD=2.7V, VCC=12V, IREF=10uA,
Frame rate=110Hz, Display on, Segment
pin under test is connected with a 20K
resistive load to VSS
Contrast = 7F
Contrast = 5F
Contrast = 3F
Contrast = 1F
270 300 370
- 225 -
- 150 - uA
- 75 -
Segment output current
Dev uniformityVDD=2.7V, VCC=12V, IREF
=10uA, Contrast=7F
Adjacent pin
Overall pin to pin
- 2-
%
--
3
VDD input=3V,
Vcc
DC-DC converter output L=22uH; R1=450Kohm;
voltage
R2=50Kohm;
10
-
12 V
Icc = 20mA(loading)
Pwr DC-DC converter output VDD input=3V, L=22uH;
power
Vcc = 12V
-
- 400 mW
RET012864Q OLED Graphic 128x64 dots
Dimension drawing
Feature
1. 128x64 dots
2. Built-in Controller SSD1325T6R1
3. +3V power supply
4. 1/64 duty cycle
5. Interface: 6800, 8080, SPI
6. Polarizer optional
No. Symbol
I/O Description
1 NC(GND)
Reserved Pin (Supporting Pin)
2 VCC P Power Supply for OLED Panel
3 VCOMH P Voltage Output High Level for COM Signal
4 IREF
I Current Reference for Brightness Adjustment
5~12 D7~D0 I/O Host Data Input/Output Bus
13 E/RD#
I Read/Write Enable or Read
14 R/W#
I Read/Write Select or Write
15 D/C#
I Data/Command Control
16 RES#
I Power Reset for Controller and Driver
17 CS#
I Chip Select
Reserved Pin
18 NC
The N.C. pins between function pins are reserved for
compatible and flexible design.
Communicating Protocol Select
19 BS2
These pins are MCU interface selection input. See the
I following table:
20 BS1
68XX-parallel 80XX-parallel Serial
BS1 0 1 0
BS2 1 1 0
21 Vdd
22 NC
23 NC
24 NC
25 NC
26 NC
27 NC
28 NC
29 Vss
P Power Supply for Logic Circuit
Reserved Pin
The N.C. pins between function pins are reserved for
compatible and flexible design.
P Ground of OLED System
30 VSL
0 Voltage Output Low Level for SEG Signal
0.90
1.40
5.695
6.695
73.00±0.2
72.00
63.41(VA)
61.41(AA)
10.0
Active Area
128*64
Pixels
3.0
5.0 2.25
Segment 0
(Column 1)
Common 12
(Row 64)
Common 74
(Row 2)
Segment 127
(Column 128)
Common 13
(Row 63)
Common 75
(Row 1)
0.48
0.45
27.83
2-R0.4±0.05
8.50±0.1
Detail DOTS
Scale 10/1
30
0.50
28.75
1
0.35
P0.5*29=14.50
15.50
Stiffener
Contact side
196
Raystar

PagesPages 1
Télécharger [ RET012864Q ]


Fiche technique recommandé

No Description détaillée Fabricant
RET012864C OLED Graphic 124x64 dots Display Raystar
Raystar
RET012864D Display Module Raystar
Raystar
RET012864E OLED Graphic 124x64 dots Display Raystar
Raystar
RET012864EYPP3N00000 OLED Module Raystar
Raystar

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche