VLT130-1001 Datasheet PDF - Snaptec
| Part Number | VLT130-1001 | |
| Description | Single and Quad Output 130W Universal Input AC/DC Power Supplies | |
| Manufacturers | Snaptec | |
| Logo |  |
|
|
There is a preview and VLT130-1001 download ( pdf file ) link at the bottom of this page. Total 4 Pages | ||
Preview 1 page No Preview Available !
VLT130 Series
Single and Quad Output 130W
Universal Input AC/DC Power Supplies
Unless stated otherwise, specifications are typical and rated at full load, nominal input
voltage, convection cooling and 25oC.
INPUT
AC Input
Auto-ranging
90 to 132V
180 to 264V
Efficiency
82%
Input Frequency
47— 63 Hz
Input Current
Full Load at Low Line 3.3Arms, max
Inrush Current
High Line
40A, max
OUTPUT
Output Power4,5
All Outputs No Fan 80W max
All Outputs With Fan 130W max
DC Output
See table
Hold-Up Time
115V/230V
15ms
Set Point Accuracy
V1 and V2
V3 and V4
+1%
+5%
Line Regulation
Low Line to High Line 0.3%
Load Regulation
Min to Full Load
V1 and V2
V3 and V4
+1%
+5%
Transient Response
50% to Full Load
Voltage Deviation
Recovery Time
<7%
<1ms
OVP
3.3V Output
5V Output
5.1V, +0.4V
6.2V, +0.4V
Overload Protection Primary Limited
195W, +35W
Short Circuit Protection Auto Recovery <6s Short Term
Ripple and Noise
V1 and V2
V3 and V4
50mV
1%
Power Fail Signal2
TTL
2ms warning
Remote Sense3
Line Compensation 450mV
on V1 and V2
Power Good2
Delay after V1 high 10ms
Output Rise Time
<10ms
Redundancy
see page 24
1+1
Paralleling Function
No
ENVIRONMENTAL
Operating Temperature
Storage Temperature
Cooling
Convection
15 CFM
Relative Humidity
Non condensing
MTBF
MIL-HDBK-217F
0 to 50oC
—40 to 85oCto
80W
130W
95%, max
>200,000 hrs
EMC AND SAFETY
CE Mark
EMC
Harmonic Correction
Agency Approvals
Safety Standards
Safety File numbers
Full compliance with the LVD
EN55022-B, CISPR22-B, FCC Part
15 Class B, EN50082-1
EN61000-3-2 Class A and D
VDE, UL, c-UL
IEC950, EN60950, UL1950 Class 1
SELV
VDE: 18934-3336
UL: E150565
MECHANICAL
AC Input Connector J1
Ground Connector
Output Connector J2
Output Connector J3
Size
Weight
Molex 3 position, 0.156 center
header 26-60-4030 or equivalent
Spade connector
Molex terminal block or equivalent
Molex 22-23-2081 or equivalent
3x5x1.07 (76.2x126.9x27.2mm)
12oz (340g)
INPUT CONNECTOR J1
Pin 1
Neutral
Pin 2
Line
Input Spade Connector
GND
Ground
OUTPUT CONNECTOR J2
Single Output Quad Output
Pin 1 No Connection
V3
Pin 2
V1B
V2
Pin 3 DC Return
DC Return
Pin 4 DC Return
DC Return
Pin 5
V1A
V1
Pin 6 No Connection
V4
OUTPUT CONNECTOR J3
Single Output
Quad Output
Pin 1* V1 Current Share V2 Current Share
Pin 2* V1 Current Share V1 Current Share
Pin 3 No Connection
Power Fail
Pin 4
Common
Common
Pin 5 -V1A Sense
-V1 Sense
Pin 6 +V1A Sense
+V1 Sense
Pin 7 +V1B Sense
+V2 Sense
Pin 8 -V1B Sense
-V2 Sense
* Pins 1 and 2 are not connected for models with no
current share
|
| |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for VLT130-1001 electronic component. |
| Information | Total 4 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ VLT130-1001.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| VLT130-1000 | The function is Single and Quad Output 130W Universal Input AC/DC Power Supplies. Snaptec | |
| VLT130-1001 | The function is Single and Quad Output 130W Universal Input AC/DC Power Supplies. Snaptec | |
| VLT130-1002 | The function is Single and Quad Output 130W Universal Input AC/DC Power Supplies. Snaptec | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
VLT1
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||