EMP2033-06VC06GRR Datasheet PDF - Elite Semiconductor
| Part Number | EMP2033-06VC06GRR | |
| Description | 300mA CMOS Linear Regulator | |
| Manufacturers | Elite Semiconductor | |
| Logo |  |
|
|
There is a preview and EMP2033-06VC06GRR download ( pdf file ) link at the bottom of this page. Total 14 Pages | ||
Preview 1 page No Preview Available !
ESMT/EMP
EMP2033
Dual, High-PSRR, Low-Noise, Low-Dropout, 300mA
CMOS Linear Regulator
General Description
The EMP2033 series is a family of dual-channel CMOS
linear regulators featuring ultra-high power supply
rejection ratio (PSRR), low output voltage noise, low
dropout voltage, low quiescent current and fast
transient response. It guarantees delivery of 300mA
output current per regulator, and supports preset
output voltages ranging from 1.2V to 3.3V with 0.1V
increment (except for 1.85V and 2.85V).
The EMP2033 is well suited for portable battery-powered
application which requires high efficiency, low noise
and small board space. With 150mV low dropout
voltage at 300mA output current, EMP2033 sustains high
PSRR at very low input voltage which is common in
battery-powered application. The EMP2033 also
features 120µVRMS low output voltage noise without the
presence of a noise bypass capacitor, which fits the
application where noise and board space are both
concerned.
Each regulator in the EMP2033 can be turned off
independently, further prolonging the battery life.
Internally build-in thermal protection and over-current
protection provide additional safety for the end use.
The EMP2033 is available in miniature 6-pin SOT-23-6,
6-pin FBP and TDFN (2x2) packages.
Typical Application Diagram
Features
Miniature SOT-23-6 and TDFN-2x2-6 packages
300mA guaranteed output current
72dB typical PSRR at 1kHz (60dB typical at 10KHz)
120µVRMS output voltage noise (10Hz to 100kHz)
150mV typical dropout at 300mA
150µA typical quiescent current
Less than 1μA typical shutdown mode
Auto-discharge during chip disable
Fast line and load transient response
30µs typical turn-on time
2.5V to 5.5V input range
Stable with small ceramic output capacitors
Over temperature and over current protection
±2% output voltage tolerance
Applications
Wireless handsets
PCMCIA cards
DSP core power
Hand-held instruments
Battery-powered systems
Portable information appliances
Typical Performance Characteristics
PSRR vs. Frequency
EMP2033
Elite Semiconductor Memory Technology Inc./Elite MicroPower Inc.
Frequency (Hz)
Publication Date : Mar. 2010
Revision : 7.2
1/14
|
| |
 
ESMT/EMP
Thermal Shutdown
TSD Temperature
Thermal Shutdown Hysteresis
TON Turn-On Time
VOUT at 95% of Final Value
TOFF Turn-Off Time
IOUT=0mA (Note 9)
EMP2033
170
℃
30
30 µs
2.4 ms
Note 1: Absolute Maximum ratings indicate limits beyond which damage may occur. Electrical specifications are not
applicable when the device is operated outside of its rated operating conditions.
Note 2: All voltages are defined and measured with respect to the potential at the ground pin.
Note 3: Maximum Power dissipation for the device is calculated using the following equations:
PD
=
TJ(MAX)
θJA
-
TA
where TJ(MAX) is the maximum junction temperature, TA is the ambient temperature, and θ JA is the
junction-to-ambient thermal resistance. E.g. for the SOT-23-6 packageθJA = 250°C/W, TJ(MAX) = 150°C and using
TA = 25°C, the maximum power dissipation is found to be 500mW. The derating factor (-1/θJA) = -4mW/°C, thus
below 25°C the power dissipation figure can be increased by 4mW per degree, and similarity decreased by this
factor for temperatures above 25°C. The value of theθJA for the DFN package is specifically dependent on the
PCB trace area, trace material, and the number of layers and thermal vias.
Note 4: Dropout voltage is measured by reducing VIN until VOUT drops 100mV from its nominal value at VIN -VOUT =1V.
Dropout voltage does not apply to the regulator versions with VOUT less than 2.5V.
Note 5: Human body model: 1.5kΩ in series with 100pF.
Note 6: Condition does not apply to input voltages below 2.5V since this is the minimum input operating voltage.
Note 7: Typical Values represent the most likely parametric norm.
Note 8: For different output voltage, the noise can be approximately calculated using the following formula:
Noise = VOUT × 42 (μVRMS )
Note 9: Turn-off time is time measured between the enable input just decreasing below VIL and the output voltage just
decreasing to 10% of its nominal value.
Elite Semiconductor Memory Technology Inc./Elite MicroPower Inc.
Publication Date : Mar. 2010
Revision : 7.2
5/14
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for EMP2033-06VC06GRR electronic component. |
| Information | Total 14 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ EMP2033-06VC06GRR.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| EMP2033-06VC06GRR | The function is 300mA CMOS Linear Regulator. Elite Semiconductor | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
EMP2
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||