|
|
PDF TC8.1A Data sheet ( Hoja de datos )
| Número de pieza | TC8.1A | |
| Descripción | Color Television Service Manual | |
| Fabricantes | Philips | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TC8.1A (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
Colour Television
Chassis
TC8.1A
CA
H_17130_000.eps
240407
Contents
Page
1. Technical Specifications, Connections, and Chassis
Overview
2
2. Safety Instructions, Warnings, and Notes
4
3. Directions for Use
5
4. Mechanical Instructions
6
5. Service Modes, Error Codes, and Fault Finding 8
6. Block Diagrams, Test Point Overview, and
Waveforms
Block Diagram Mono Carrier
15
7. Circuit Diagrams and PWB Layouts
Mono Carrier
(A) 16
CRT Panel
(B) 19
Side AV & I/O Panel
(E) 21
8. Alignments
23
9. Circuit Descriptions, Abbreviation List, and IC Data
Sheets
28
Abbreviation List
33
10. Spare Parts List
34
11. Revision List
37
17-18
20
21
©Copyright 2007 Philips Consumer Electronics B.V. Eindhoven, The Netherlands.
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system or transmitted, in any form or by any means, electronic,
mechanical, photocopying, or otherwise without the prior permission of Philips.
Published by WS 0764 BG CD Customer Service Printed in the Netherlands
Subject to modification
EN 3122 785 17130
1 page  
Directions for Use
TC8.1A CA
3. EN 5
2.4.2 Schematic Notes
• All resistor values are in ohms, and the value multiplier is
often used to indicate the decimal point location (e.g. 2K2
indicates 2.2 kohm).
• Resistor values with no multiplier may be indicated with
either an "E" or an "R" (e.g. 220E or 220R indicates 220
ohm).
• All capacitor values are given in micro-farads (μ= x10-6),
nano-farads (n= x10-9), or pico-farads (p= x10-12).
• Capacitor values may also use the value multiplier as the
decimal point indication (e.g. 2p2 indicates 2.2 pF).
• An "asterisk" (*) indicates component usage varies. Refer
to the diversity tables for the correct values.
• The correct component values are listed in the Spare Parts
List. Therefore, always check this list when there is any
doubt.
2.4.3 Lead-free Soldering
Due to lead-free technology some rules have to be respected
by the workshop during a repair:
• Use only lead-free soldering tin Philips SAC305 with order
code 0622 149 00106. If lead-free solder paste is required,
please contact the manufacturer of your soldering
equipment. In general, use of solder paste within
workshops should be avoided because paste is not easy to
store and to handle.
• Use only adequate solder tools applicable for lead-free
soldering tin. The solder tool must be able:
– To reach a solder-tip temperature of at least 400°C.
– To stabilize the adjusted temperature at the solder-tip.
– To exchange solder-tips for different applications.
• Adjust your solder tool so that a temperature of around
360°C - 380°C is reached and stabilized at the solder joint.
Heating time of the solder-joint should not exceed ~ 4 sec.
Avoid temperatures above 400°C, otherwise wear-out of
tips will increase drastically and flux-fluid will be destroyed.
To avoid wear-out of tips, switch “off” unused equipment or
reduce heat.
• Mix of lead-free soldering tin/parts with leaded soldering
tin/parts is possible but PHILIPS recommends strongly to
avoid mixed regimes. If this cannot be avoided, carefully
clear the solder-joint from old tin and re-solder with new tin.
2.4.4 Alternative BOM identification
The third digit in the serial number (example:
BF2A0635000001) indicates the number of the alternative
B.O.M. (Bill Of Materials) that has been used for producing the
specific TV set. In general, it is possible that the same TV
model on the market is produced with e.g. two different types
of displays, coming from two different suppliers. This will then
result in sets which have the same CTN (Commercial Type
Number; e.g. 28PW9515/12) but which have a different B.O.M.
number.
By looking at the third digit of the serial number, one can
identify which B.O.M. is used for the TV set he is working with.
If the third digit of the serial number contains the number “1”
(example: BF1A063500001), then the TV set has been
manufactured according to B.O.M. number 1. If the third digit is
a “2” (example: BF2A0635000001), then the set has been
produced according to B.O.M. no. 2. This is important for
ordering the correct spare parts!
For the third digit, the numbers 1...9 and the characters A...Z
can be used, so in total: 9 plus 26= 35 different B.O.M.s can be
indicated by the third digit of the serial number.
Identification: The bottom line of a type plate gives a 14-digit
serial number. Digits 1 and 2 refer to the production center (e.g.
AG is Bruges), digit 3 refers to the B.O.M. code, digit 4 refers
to the Service version change code, digits 5 and 6 refer to the
production year, and digits 7 and 8 refer to production week (in
example below it is 2006 week 17). The 6 last digits contain the
serial number.
MODEL : 32PF9968/10
PROD.NO: AG 1A0617 000001
MADE IN BELGIUM
220-240V ~ 50/60Hz
128W
VHF+S+H+UHF
S BJ3.0E LA
E_06532_024.eps
130606
Figure 2-2 Serial number (example)
2.4.5 Practical Service Precautions
• It makes sense to avoid exposure to electrical shock.
While some sources are expected to have a possible
dangerous impact, others of quite high potential are of
limited current and are sometimes held in less regard.
• Always respect voltages. While some may not be
dangerous in themselves, they can cause unexpected
reactions that are best avoided. Before reaching into a
powered TV set, it is best to test the high voltage insulation.
It is easy to do, and is a good service precaution.
3. Directions for Use
You can download this information from the following websites:
http://www.philips.com/support
http://www.p4c.philips.com
5 Page 
5.3.6 One Horizontal Line
Service Modes, Error Codes, and Fault Finding
TC8.1A CA
5. EN 11
One horizontal line
Check
Deflection yoke
Terminal OK?
Yes
No
Check
+24v supply
Pin 2 of IC 301
OK?
Yes
No
Check
V output
Pin 5 of IC 301
OK?
No
Yes
Check
R314, C301,
R317,R336, C309
Replace
Yoke coil
Check
R405 (Fuse)
D402
Check
V input
Pin 1 of IC 301
OK?
No
Check
V output
Pin 16 of IC 201
Figure 5-6 Flow chart “One Horizontal Line”.
H_17130_015.eps
070507
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet TC8.1A.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TC8.1A | Color Television Service Manual | Philips |
| TC8.1L | Color Television Service Manual | Philips |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |