|
|
PDF AGQ100-48S12 Data sheet ( Hoja de datos )
| Número de pieza | AGQ100-48S12 | |
| Descripción | Quarter-brick Converter | |
| Fabricantes | EMERSON | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de AGQ100-48S12 (archivo pdf) en la parte inferior de esta página. Total 16 Páginas | ||
|
No Preview Available !
48Vdc Input,[email protected] Output
Quarter-Brick Converter AGQ100-48S12
Description
The AGQ100-48S12 is a single output DC-DC
converter with standard quarter-brick outline
and pin configuration. It delivers up to 8.3A
output current with 12.0V output voltage.
Above 92.9% efficiency and excellent thermal
performance make it an ideal choice to supply
power in telecom and datacom application. It
can work under -40°C ~ +85°C.
Operational Features
Delivering up to 8.3A output current
High efficiency: 92.9% typ., at full load
Wide input range: 36V ~ 75V
Excellent thermal performance
No minimum load requirement
RoHS 5 compliant
Control Features
Remote control function (negative
positive logic optional)
Remote output sense
Trim function: -20% ~ +10%
or
Protection Features
Input under voltage lockout
Output over current protection
Output over voltage protection
Over temperature protection
Mechanical Features
Industry standard quarter-brick pin-out
outline
Open frame structure
Pin length: 3.8mm
Safety & EMC
Meet latest safety standards UL 60950-1,
CSA-C22.2 NO.60950-1, IEC/EN 60950-1
and GB4943
Approved by UL and TUV
Meet 2006/95/EEC and 93/68/EEC
directives which facilitate CE marking in
user’s end product
Meet conducted emission's requirements
of FCC Class A and EN55022 Class A,
tested with external filter
Material meets UL 94-V0
Document NO.: 31020767
May 18, 2010
Rev 1.0
http://www.Datasheet4U.com
1 page  
AGQ100-48S12 DC-DC Converter TRN
5/16
Electromagnetic Compatibility Requirements
Test item
Conducted emission
Immunity to electrostatic discharge
Immunity to electrical fast transient
Immunity to surges
Immunity to continuous conducted
interference
Immunity to voltage dips and short
interruptions and voltage variations
Regulations
EN 55022
DC input port, Class A
IEC/EN61000-4-2
Enclosure port, Level 3
IEC/EN61000-4-4
DC input port, Level 3
IEC/EN61000-4-5
DC input port
Line to Ground (earth): 600V
Line to Lineline: 600V
IEC/EN61000-4-6
DC input port, Level 2
EN 61000-4-29
DC input port
Criteria
B
B
B
A
B
Notes & conditions
See EMC Test Conditions
Criterion A: Normal performance during and after test.
Criterion B: For EFT and surges, low-voltage protection or reset is not allowed. Temporary output
voltage fluctuation ceases after disturbances ceases, and from which the EUT recovers its normal
performance automatically.
For Dips and ESD, output voltage fluctuation or reset is allowed during the test, but recovers to its
normal performance automatically after the disturbance ceases.
Criterion C: Temporary loss of output, the correction of which requires operator intervention.
Criterion D: Loss of output which is not recoverable, owing to damage to hardware.
http://www.emersonnetworkpower.com.cn
5 Page 
AVQ100-48S12 DC-DC Converter TRN
11/16
Sense Characteristics
If the load is far from the unit, connect S+ and S- to the terminal of the load respectively to
compensate the voltage drop on the transmission line. If the sense compensate function is not
necessary, connect S+ to Vo+ and S- to Vo- directly.
Input Ripple & Inrush Current And Output Ripple & Noise Test
Configuration
Current probe
L1
Vin+
Probe
50mm
Vo+
Cin
Vdc
C1 C2
DC/DC
C3 C4
Vin- Vo-
Load
Figure 16 Input ripple & inrush current, output ripple & noise test configuration
Vdc: DC power supply
L1: 12µH
Cin: 220µF/100V typical
C1 ~ C4: See Figure 11
Note: It is recommended to use a coaxial cable with series 50Ω resistor and 0.68µF ceramic
capacitor or a ground ring of probe to test output ripple & noise.
EMC Test Conditions
The customer actual EMI circuit is shown in the following figure.
U1 U2
In+
Cx
Cy1
Cy2
1mH
In-
PE
EMI filter
Out+
Vin+
C1 C2
DC/DC
VO+
Out-
Vin- VO-
C3 C4
Resistive Load
Figure 17 EMC test configuration
CX: 1µF/100V ceramic capacitor, C3225X7R2A225KT0LOU/TDK
Cy1, Cy2: 2200pF/1000V ceramic capacitor, GHM1535X7R223K1KD550/MURATA
C1: 0.1µF/100V ceramic capacitor, C1206X7R2A105KT0L0U/TDK
C2: 100µF/100V low ESR aluminum electrolytic capacitor, UVZ2A101MPD
C3: 1µF/25V ceramic capacitor, C2012X7R1E105KT000N/TDK
C4: 220µF/100V low ESR aluminum electrolytic capacitor, UPM1E221MHD
http://www.emersonnetworkpower.com.cn
11 Page | ||
| Páginas | Total 16 Páginas | |
| PDF Descargar | [ Datasheet AGQ100-48S12.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| AGQ100-48S12 | Quarter-brick Converter | EMERSON |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |