|
|
PDF TD100 Data sheet ( Hoja de datos )
| Número de pieza | TD100 | |
| Descripción | Pressure Transducer Displays | |
| Fabricantes | Celerity | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TD100 (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
|
No Preview Available !
TD100 Series
Pressure Transducer Displays
Celerity, Inc.
915 Enterprise Boulevard
Allen, TX 75013 USA
T +1 972 359 4000
F +1 972 359 4100
153-30268-000 REV. 002 05/08
User Guide
Free Datasheet http://www.Datasheet4U.com
1 page  
_DESCRIPTION
1.6 TD100 SPECIFICATIONS
Category
Features
4-20 mA
Measuring units available
Setpoint indication and
contact switching
Swivel around transducer
for better viewing angle
Two user programmable/
adjustable alarm setpoints
Display
Accuracy
Conversion rate
Decimal point
Digital damping
Digits and type
Polarity
Range
Temperature coefficient
Value update
Material
Housing
Digit height/width
Pigtail length
Stability, vibration
Stability, shock
Shipping weight (approx.)
Electrical
Power requirements
Input
Input connections
Output connections
Pressure warnings
Setpoint contact rating
Resistive load
Inductance
Switching cycles
Protection Short
Reverse
Access
Data storage
Environmental
Temperature range
Operating
Storage
Compliance
CE
RoHS
Specification
Yes
Programmable zero and full scale
Available
Yes
Yes
+/-0.1%
10 times/second
User adjustable
0.3 to 3 seconds (programmable)
4 digit, red LED with 7 segments
Automatic (-) displayed in vacuum
-1999 to +9999
+/-0.1% FS/degree F
0.1 to 10 seconds
Aluminum, powder coating
9 mm/5.4 mm
2 M standard, (optional lengths upon request)
15 Grm 10-2000 Hz (Mil-Std-202M20 Cond. B)
50 g, 11 msec (Mil-Std-202, M213 Cond. G)
200 g
Voltage drop <4.5; Minimum lit-up current 3 mA
4-20 mA (2 wire, loop powered)
Back mount, 4-pin female Bendix connector, factory wired for 4-20
mA transducer
Bottom mount, 4-pin female connector, factory wired for 4-20 mA
transducer
Top mount, pigtail, 6 wire cable
Top mount, male Bendix 4-pin connector
2 switched setpints for pigtail; 2 visual setpoints for 4-pin Bendix (no
switch output)
125 mA maximum and 26 Vdc. electrically isolated
10 K ohm maximum
4.7 mH
>80 K
Permanent short circuit protection
No damage at reverse polarity, but no function
Password protection
EPROM, 4 K maximum
-20 to 85oC
-40 to 85oC
Compliant to EMC directive EN61326
Compliant to EU directive 2002/95/EC
p.3
Free Datasheet http://www.Datasheet4U.com
5 Page 
_OPERATION
3.3 OPERATING THE USER MENU
The TD100 must be setup to read the transducer unit setting, zero setpoint,
span setpoint, alarms, and other functions. These settings are established from
the User Menu as described in Figure 12.
MEASURE
Press and hold UP button for 2 seconds.
0000
Input password
CODE
DOWN
button
0000
UP button
DOT -
DOWN
button
.
UP button
.
0.0 0 0
DOWN
SET0 button
UP button
SETF
DOWN
button
UP button
ALAL
DOWN
button
UP button
DN
DOWN
button
UP button
ALAH
DOWN
button
UP button
UP
DOWN
button
UP button
AUAP
DOWN
button
0.0 0 0
1.0 0 0
0.3 0 0
DN
9.0 0 0
UP
0.3
1. Measure Mode (MEASURE):
a. Press and hold the UP button for 2 seconds. All zeros should appear. (This is
the default password) If is has not changed, press the DOWN button 4 times to
enter Configuration menu.
b. If the password has changed, press the DOWN button to enter password and
to access Configuration Menu.
2. Setting Configuration Menu Password (CODE):
a. Enter Configuration Menu with CODE displayed on LED, or current password.
b. Press the DOWN button. 0000 should be displayed and the first digit should
be flashing.
c. Press the UP button to amend value, or press the DOWN button to move the
cursor until password setting is complete. Default password: 0000 Admin
password: 0700
3. Unit Setting (DOT):
a. Press the UP button to set unit.
b. Press the DOWN button to set unit and to return to previous menu.
4. Zero Setting (SET0):
a. Press the UP button to change value.
b. Press the DOWN button to move the cursor, to complete the setting, to
save the data, and to return to previous menu.
5. Span Setting (SETF):
a: . Press the UP button to change value.
b. Press the DOWN button to move the cursor, to complete the setting, to
save the data, and to return to previous menu.
6. Low-Alarm Setpoint (ALAL):
a. Press the UP button to change value.
b. Press the DOWN button to move the cursor, to complete the setting, to
save the data, and to return to previous menu.
7. Low-Alarm Direction Setting :
a. Press the UP button to change value.
b. Press the DOWN button to move the cursor, to complete the setting, to
save the data, and to return to previous menu.
8. High-Alarm Setpoint (ALAH):
a. Press the UP button to change value.
b. Press the DOWN button to move the cursor, to complete the setting, to
save the data, and to return to previous menu.
9. High-Alarm Direction Setting :
a. Press the UP button to change value.
b. Press the DOWN button to move the cursor, to complete the setting, to
save the data, and to return to previous menu.
10. Digital Damping Setting (AUAP):
a. Press the UP button to change value. Value range (0.3-3.0 seconds; default
is 0.3 seconds)
b. Press the DOWN button to move the cursor, to complete the setting, to
save the data, and to return to previous menu.
11. Value Update Setting (AUSP):
a. Press the UP button to change value. Value range (0.1-10.0 seconds; default
is 0.1 seconds)
b. Press the DOWN button to move the cursor, to complete the setting, to
save the data, and to return to previous menu.
12. Low Signal Reset Setting (ASCP):
a. Press the UP button to change value. Value range (0 -100%; default is 0.5%)
b. Press the DOWN button to move the cursor, to complete the setting, to
save the data, and to return to previous menu.
13. Data Initialization (DEF-):
The LED displays DEF- and flashes. Press and hold the UP button for 3
seconds. The LED displays _ _ _ _. All user data is initialized.
UP button
AUSP
DOWN
button
0.1
UP button
ASCP
UP button
DEF -
DOWN
button
DOWN
button
0 0 0.5
DEF -
Figure 12: User Menu Operation
p.9
Free Datasheet http://www.Datasheet4U.com
11 Page | ||
| Páginas | Total 14 Páginas | |
| PDF Descargar | [ Datasheet TD100.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TD100 | ThinkServer Manual |  lenovo |
| TD100 | Pressure Transducer Displays | Celerity |
| TD100x | ThinkServer Manual | lenovo |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |