|
|
PDF V375A15C600A Data sheet ( Hoja de datos )
| Número de pieza | V375A15C600A | |
| Descripción | DC-DC Converter Module | |
| Fabricantes | VICOR | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de V375A15C600A (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
45
Features
• DC input range: 250 - 425V
• Input surge withstand: 500V for 100ms
• DC output: 15V
• Programmable output: 10 to 110%
• Regulation: ±0.2% no load to full load
• Efficiency: 87%
• Maximum operating temperature:
100°C at full load
• Power density: 119W/cubic inch
• Height above board: 0.43 in. (10,9 mm)
• Parallelable, with N+M fault tolerance
• Low noise ZCS/ZVS architecture
375Vin / 15Vout / 600Watts
DC-DC Converter Module
Model Number V375A15C600A*
Typical Applications: distributed power;
off-line systems using power PFC front-ends;
electric vehicles
Shown actual size:
4.6 x 2.2 x 0.5 in
117 x 56 x 12,7 mm
Product Overview
Absolute Maximum Ratings
This DC-DC converter module uses
2nd Generation power processing, control
and packaging technologies to provide the
performance, flexibility and cost effectiveness
expected of a mature power component.
Parameter
+In to –In voltage
+In to –In voltage
Rating
-0.5 to +425.0
500
For example, a plated-cavity core transformer PC to –In voltage
-0.5 to +7.0
couples widely separated primary and
PR to –In voltage
-0.5 to +7.0
secondary windings, resulting in low in-to-
out parasitic capacitance and noise.
High frequency ZCS/ZVS switching,
advanced power semiconductor packaging
+Out to –Out voltage
+Sense to –Out voltage
–Sense to –Out voltage
-0.5 to +20.0
-0.5 to +20.0
1.0
and thermal management provide high
SC to –Out voltage
-0.5 to +1.5
power density with low temperature
gradients. Extensive use of silicon
integration results in 1/3 the part count
of a 1st Generation converter.
Isolation voltage (in to out)
Isolation voltage (in to base)
Isolation voltage (out to base)
3000
1550
500
* Part Numbering
Storage temperature (C–Grade) -40 to +125
Operating temperature (C–Grade) -20 to +100
V 375 A 5 C 400 A
Input Voltage
24 = 24Vin
48 = 48Vin
300 = 300Vin
375 = 375Vin
A = Maxi
B = Mini
C = Micro
Output
Voltage
Output
Power
Pin
Style
Product Grade Temperatures (°C)
Grade Storage Operating
C = - 40 to +125 - 20 to +100
T = - 40 to +125 - 40 to +100
H = - 55 to +125 - 40 to +100
M = - 65 to +125 - 55 to +100
Base-
plate
Pin soldering temperature
Pin soldering temperature
Mounting torque
500 (260)
750 (390)
5 (0.57)
Thermal Resistance and Capacity
Parameter
Min
For pin styles see page 6. Slotted baseplate
(style 1) requires no designator. For
threaded baseplate add a “2” to the end of
the part number. For thru-hole, add a “3”.
See page 7 for dimensions.
Baseplate to sink; flat, greased surface
Baseplate to sink; thermal pad (P/N 20263)
Baseplate to ambient
Baseplate to ambient; 1000 LFM
Thermal capacity
Unit
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Vrms
Vrms
Vrms
°C
°C
°F (°C)
°F (°C)
in-lbs (N-m)
Notes
<100ms
See part numbering chart on this
page for other product grades.
Baseplate
<5 sec; wave solder
<7 sec; hand solder
6 each, # 4-40 or M3
Typ Max Unit
0.08 °C/Watt
0.07 °C/Watt
4.9 °C/Watt
1.1 °C/Watt
165 Watt-sec/°C
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
V375A15C600A DC-DC Converter
Set your site on VICOR at www.vicorpower.com
Rev. 5.2
Page 1 of 8
Free Datasheet http://www.Datasheet4U.com
1 page  
CONTROL FUNCTIONS - SC PIN
Output Voltage Programming
The output voltage of the converter can be adjusted or
programmed via fixed resistors, potentiometers or voltage
DACs. See Figures 7 and 8.
Error
Amp
1kΩ
0.033µF
1.23V
+Out
+S
SC
–S
–Out
RD
Trim Down
Load
Error
Amp
1kΩ
0.033µF
1.23V
+Out
+S
SC
–S
–Out
RU
Trim Up
Load
RD (ohms) =
1,000 Vout
Vnom - Vout
Figure 7—Output voltage trim down circuit.
1,000 (Vout-1.23) Vnom
RU (ohms) = 1.23 (Vout-Vnom) –1,000
Figure 8—Output voltage trim up circuit.
Trim Down
1. This converter is not a constant power device – it has a
constant current limit. Hence, available output power is
reduced by the same percentage that output voltage is
trimmed down. Do not exceed maximum rated output current.
2. The trim down resistor must be connected to the –Sense pin.
Trim Up
1. The converter is rated for a maximum delivered power. To ensure
that maximum rated power is not exceeded, reduce maximum
output current by the same percentage increase in output voltage.
2. The trim up resistor must be connected to the +Sense pin.
3. Do not trim the converter above maximum trim range
(typically +10%) or the output over voltage
protection circuitry may be activated.
Trim resistor values calculated automatically:
On-line calculators for trim resistor values are available
on the vicor website at: vicorpower.com/tools.html.
Resistor values can be calculated for fixed trim up, fixed
trim down and for variable trim up or down cases for both
1st and 2nd Generation DC-DC converters.
In addition to trimming information, the web site and the
Applications Manual also include design tips, applications
circuits, EMC suggestions, thermal design guidelines and
PDF data sheets for all available Vicor products.
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
V375A15C600A DC-DC Converter
Set your site on VICOR at www.vicorpower.com
Rev. 5.2
Page 5 of 8
Free Datasheet http://www.Datasheet4U.com
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet V375A15C600A.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| V375A15C600A | DC-DC Converter Module | VICOR |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |