|
|
PDF SF2133E Data sheet ( Hoja de datos )
| Número de pieza | SF2133E | |
| Descripción | SAW Filter | |
| Fabricantes | RFM | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SF2133E (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
|
No Preview Available !
• Low Loss SAW Filter
• Surface Mount 3.0 x 3.0 mm Package
• Complies with Directive 2002/95/EC (RoHS)
Pb
Absolute Maximum Ratings
Rating
Input Power Level
DC Voltage on any Non-ground Terminal
Operating Temperature Range
Storage Temperature Range in Tape and Reel
Maximum Soldering Profile, 5 cycles/10 seconds maximum
Value
5
3
-40 to +85
-40 to +90
265
Units
dBm
V
°C
°C
°C
SF2133E
1747.50 MHz
SAW Filter
Electrical Characteristics
Characteristic
Center Frequency
Insertion Loss, 1710 to 1785 MHz
Amplitude Ripple, 1710 to 1785 MHz
Attenuation Referenced to 0 dB:
10 to 1670 MHz
1670 to 1690 MHz
1805 to 1880 MHz
1880 to 4500 MHz
4500 to 5000 MHz
Input/Output VSWR, 1710 to 1785 MHz
Source Impedance
Load Impedance
Case Style
Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator
Standard Reel Quantity
Reel Size 7 Inch
Reel Size 13 Inch
Electrical Connections
Connection
Input
Output
Case Ground
Terminals
2
5
All others
Sym
fC
IL
ZS
ZL
SM3030-6
Notes Min
Typ
1747.5
2.6
1.6
Max
-20 to +70 °C
4.0
2.5
Max
-40 to +85 °C
4.1
2.8
15 23
6 23.9
6 24
15 25
10 14
1.8:1
50
50
2.5:1
2.5:1
SM3030-6 3.0 x 3.0 mm Nominal Footprint
679, YWWS
500 Pieces/Reel
3000 Pieces/Reel
Units
MHz
dB
dBP-P
dB
Ω
Ω
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
Notes:
1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance
matching to 50 Ω and measured with 50 Ω network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external
impedance matching design. See Application Note No. 42 for details.
4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."
5. The design, manufacturing process, and specifications of this filter are subject to change.
6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port
2, so that the filter must always be installed in one direction per the circuit design.
7. US and international patents may apply.
8. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc.
www.RFM.com E-mail: [email protected]
© 2009-2011 by RF Monolithics, Inc.
Page 1 of 5
SF2133E - 9/21/11
Free Datasheet http://www.datasheetlist.com/
1 page  
Tape and Reel Specifications
See Detail "A"
Inches
7
13
“B”
millimeters
178
330
Quantity Per Reel
500
3000
12.0
2.0
COMPONENT ORIENTATION and DIMENSIONS
Carrier Tape Dimensions
Ao
Bo
Ko
Pitch
W
0.3 ± 0.05
2.0 4.0
PIN #1
1.50 A
RO.3
(MAX.)
Bo
Ko
SECTION A-A
B
Ao
B
Pitch
A
R0.5
(MAX.)
1.5
SECTION B-B
USER DIRECTION OF FEED
www.RFM.com E-mail: [email protected]
© 2009-2011 by RF Monolithics, Inc.
3.35 mm
3.35 mm
1.40 mm
8.0 mm
12.0 mm
Page 5 of 5
SF2133E - 9/21/11
Free Datasheet http://www.datasheetlist.com/
5 Page | ||
| Páginas | Total 5 Páginas | |
| PDF Descargar | [ Datasheet SF2133E.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SF2133E | SAW Filter | RFM |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |