DataSheetWiki


SF1080A fiches techniques PDF

RFM - 499.25 MHz SAW Filter

Numéro de référence SF1080A
Description 499.25 MHz SAW Filter
Fabricant RFM 
Logo RFM 





1 Page

No Preview Available !





SF1080A fiche technique
• Designed for CATV Applications (Pilot Tone)
• Tightly-controlled Insertion Loss
• 9.1 x 7.1 mm Surface-mount Case
• Unbalanced Input and Output
• Complies with Directive 2002/95/EC (RoHS) Pb
SF1080A
499.25 MHz
SAW Filter
Absolute Maximum Ratings
Rating
Maximum Incident Power in Passband
Maximum DC Voltage between any 2 Terminals
Storage Temperature Range
Suitable for lead-free soldering - Max Soldering Profile
Value
Units
+10 dBm
30 VDC
-54 to +85
°C
260°C for 30 s
SM9171-10
Electrical Characteristics
Characteristic
Sym
Notes
Min
Typ
Max Units
Nominal Center Frequency
Passband
Insertion Loss at fc
fC
IL
1
499.250
6.0 7.5 9.0
MHz
dB
0.5 dB Passband
3 dB Passband
Amplitude Ripple over fc ±100 kHz
BW0.5
BW3
1, 2
±100
±800
±970
kHz
0.5 dBP-P
Rejection
fc-200 to fc-3.0 and fc+3.0 to fc+200 MHz
Ultimate
1, 2, 3
35
40
dB
Operating Temperature Range
TA 1
-25
+75 °C
Impedance Matching to 50 unbalanced
Case Style
Lid Symbolization (XX = 2 character date code)
External L-C
SM9171-10 9.1 x 7.1 mm Nominal Footprint
RFM SF1080A XX
Electrical Connections
Connection
Port 1 Hot
Port 1 Gnd Return
Port 2 Hot
Port 2 Gnd Return
Case Ground
Terminals
10
1
5
6
All others
Notes:
1. Unless noted otherwise, all specitication apply over the operating temperature range with filter soldered to the specified demonstration board with
impedanced matching to 50 network analyzer.
2. Unless noted otherwise, all frequency specitications are referenced to the nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout
and external impedance matching design. See Application Note No. 42 for details.
4. “LRIP” or “L” after the part number indicates “low rate initial production” and “ENG” or “E” indicates “engineering prototypes.”
5. The design, manufacturing process, and specifications of this filter are subject to change.
6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port
1 and Port 2, so that the filter must always be installed in one direction per the circuit design.
7. US and international patents may apply.
8. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc.
9. Electrostatic Sensitive Device. Observe precautions for handling.
www.RFM.com E-mail: [email protected]
©2001-2011 by RF Monolithics, Inc.
Page 1 of 3
SF1080A 1/27/11
Free Datasheet http://www.datasheetlist.com/

PagesPages 3
Télécharger [ SF1080A ]


Fiche technique recommandé

No Description détaillée Fabricant
SF1080A 499.25 MHz SAW Filter RFM
RFM

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche