HI-8281CJT Datasheet PDF - Holt Integrated Circuits
| Part Number | HI-8281CJT | |
| Description | ARINC 429 LINE DRIVER AND DUAL RECEICER | |
| Manufacturers | Holt Integrated Circuits | |
| Logo |  |
|
|
There is a preview and HI-8281CJT download ( pdf file ) link at the bottom of this page. Total 14 Pages | ||
Preview 1 page No Preview Available !
HI-8281
January 2001
GENERAL DESCRIPTION
The HI-8281 device from Holt Integrated Circuits is a silicon
gate CMOS device for interfacing a 16-bit parallel data bus
directly to the ARINC 429 serial bus. The device provides
two receivers, an independent transmitter and line driver
capability in a single package. The receiver input circuitry
and logic are designed to meet the ARINC 429
specifications for loading, level detection, timing, and
protocol. The transmitter section provides the ARINC 429
communication protocol and the line driver circuits provide
the ARINC 429 output levels.
The 16-bit parallel data bus exchanges the 32-bit ARINC
data word in two steps when either loading the transmitter
or interrogating the receivers. The data bus interfaces with
CMOS and TTL.
Timing of all the circuitry begins with the master clock input,
CLK. For ARINC 429 applications, the master clock
frequency is 1 MHz.
Each independent receiver monitors the data stream with a
sampling rate 10 times the data rate. The sampling rate is
software selectable at either 1MHz or 125KHz. The results
of a parity check are available as the 32nd ARINC bit. The
HI-8281 examines the null and data timings and will reject
erroneous patterns. For example, with a 125 KHz clock
selection, the data frequency must be between 10.4 KHz
and 15.6 KHz.
The transmitter has a First In, First Out (FIFO) memory to
store 8 ARINC words for transmission. The data rate of the
transmitter is software selectable by dividing the master
clock, CLK, by either 10 or 80. The master clock is used to
set the timing of the ARINC transmission within the required
resolution.
FEATURES
! ARINC specification 429 compatible
! Direct receiver and transmitter interface to
ARINC bus in a single device.
! 16-Bit parallel data bus.
! Timing control 10 times the data rate
! Selectable data clocks
! Receiver error rejection per ARINC
specification 429
! Automatic transmitter data timing
! Self test mode
! Parity functions
! Low power
! Industrial & full military temperature ranges
PIN CONFIGURATION (Top View)
APPLICATIONS
! Avionics data communication
! Serial to parallel conversion
! Parallel to serial conversion
(See page 4-27 for additional pin configuration)
(DS8281 Rev. A)
HOLT INTEGRATED CIRCUITS
1
01/01
|
| |
 
HI-8281
TRANSMITTER
A block diagram of the transmitter section is shown in Figure 3.
FIFO OPERATION
The FIFO is loaded sequentially by first pulsing PL1 to load byte 1
and then PL2 to load byte 2. The control logic automatically loads
the 31 bit word in the next available position of the FIFO. If TX/R,
the transmitter ready flag is high (FIFO empty), then 8 words,
each 31 bits long, may be loaded. If TX/R is low, then only the
available positions may be loaded. If all 8 positions are full, the
FIFO ignores further attempts to load data.
DATA TRANSMISSION
When ENTX goes high, enabling transmission, the FIFO
positions are incremented with the top register loading into the
data transmission shift register. Within 2.5 data clocks the first
data bit appears at either 429DO or 429DO. The 31 bits in the
data transmission shift register are presented sequentially to the
outputs in the ARINC 429 format with the following timing:
ARINC DATA BIT TIME
DATA BIT TIME
NULL BIT TIME
WORD GAP TIME
HIGH SPEED
10 Clocks
5 Clocks
5 Clocks
40 Clocks
LOW SPEED
80 Clocks
40 Clocks
40 Clocks
320 Clocks
The word counter detects when all loaded positions are
transmitted and sets the transmitter ready flag, TX/R, high.
TRANSMITTER PARITY
The parity generator counts the ONES in the 31-bit word. If the
BD12 control word bit is set low, the 32nd bit transmitted will make
parity odd. If the control bit is high the parity is even.
SELF TEST
If the BD05 control word bit is set low, 429DO or 429DO become
inputs to the receiver bypassing the interface circuitry.
SYSTEMOPERATION
The two receivers are independent of the transmitter. Therefore,
control of data exchanges are strictly at the option of the user. The
only restrictions are:
1. The received data may be overwritten if not retrieved
within one ARINC word cycle.
2. The FIFO can store 8 words maximum and ignores
attempts to load addition data if full.
3. Byte 1 of the transmitter data must be loaded first.
4. Either byte of the received data may be retrieved first.
Both bytes must be retrieved to clear the data ready flag.
5. After ENTX, transmission enable ,goes high it cannot go
low until TX/R, transmitter readyflag, goes high. Otherwise,
one ARINC word is lost during transmission.
HOLT INTEGRATED CIRCUITS
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for HI-8281CJT electronic component. |
| Information | Total 14 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ HI-8281CJT.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| HI-8281CJI | The function is ARINC 429 LINE DRIVER AND DUAL RECEICER. Holt Integrated Circuits | |
| HI-8281CJT | The function is ARINC 429 LINE DRIVER AND DUAL RECEICER. Holt Integrated Circuits | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
HI-8
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||