DataSheetWiki


HIP1013 fiches techniques PDF

Intersil Corporation - Low Cost Dual Power Distribution Controller

Numéro de référence HIP1013
Description Low Cost Dual Power Distribution Controller
Fabricant Intersil Corporation 
Logo Intersil Corporation 





1 Page

No Preview Available !





HIP1013 fiche technique
®
Data Sheet
August 2004
HIP1013
FN4516.3
Low Cost Dual Power Distribution
Controller
The HIP1013 is a low cost HOT SWAP dual supply power
distribution controller. Two external N-Channel MOSFETs are
driven to distribute power while providing load fault isolation. At
turn-on, the gate of each external N-Channel MOSFET is
charged with a 10µA current source. Capacitors on each gate
(see the Typical Application Diagram), create a programmable
ramp (soft turn-on) to control inrush currents. A built in charge
pump supplies the gate drive for the 12V supply N-Channel
MOSFET switch.
Over current protection is facilitated by two external current
sense resistors. When the current through either resistor
exceeds the user programmed value the N-Channel MOSFETs
are latched off by the HIP1013. The controller is reset by a
rising edge on either PWRON pin.
Choosing the voltage selection mode the HIP1013 controls
either +12V/5V or +3.3V/+5V supplies.
Although pin compatible with the HIP1012 device, the HIP1013
does not offer current regulation during an OC event.
Ordering Information
PART
NUMBER
TEMP.
RANGE (°C)
PACKAGE
PKG.
DWG. #
HIP1013CB
-0 to 70
14 Ld SOIC
M14.15
HIP1013CBZA (Note)
-0 to 70
14 Ld SOIC
(Pb-free)
M14.15
NOTE: Intersil Pb-free products employ special Pb-free material
sets; molding compounds/die attach materials and 100% matte tin
plate termination finish, which is compatible with both SnPb and
Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed
the Pb-free requirements of IPC/JEDEC J Std-020B.
*Tape & Reel packaging available with “-T” suffix..
Pinout
HIP1013 (SOIC)
TOP VIEW
3/12VS 1
3/12VG 2
VDD 3
MODE/ 4
PWRON1
PWRON2 5
5VG 6
5VS 7
14 3/12VISEN
13 RILIM
12 GND
11 CPUMP
10 NC
9 PGOOD
8 5VISEN
Features
• HOT SWAP Dual Power Distribution Control for +5V and
+12V or +5V and +3.3V
• Provides Fault Isolation
• Charge Pump Allows the Use of N-Channel MOSFETs
• Redundant Power On Controls
• Power Good and Over Current Latch Indicators
• Adjustable Turn-On Ramp
• Protection During Turn-On
• Pb-free Available
Applications
• Power Distribution Control
• Hot Plug™ Components
Typical Application Diagram
CPUMP
12V
VDD
CGATE
POWER ON
INPUTS
5V
CGATE
RSENSE
HIP1013
3/12VISEN
3/12VS
3/12VG
VDD
M/PON1
RILIM
GND
CPUMP
PWRON2
NC
5VG
PGOOD
5VS 5ISEN
RSENSE
RLOAD
RILIM
5V
RLOAD
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 1998, 1999, 2004. All Rights Reserved
Hot Plug™ is a trademark of Core International, Inc. All other trademarks mentioned are the property of their respective owners.

PagesPages 8
Télécharger [ HIP1013 ]


Fiche technique recommandé

No Description détaillée Fabricant
HIP1011 PCI Hot Plug Controller Intersil Corporation
Intersil Corporation
HIP1011A PCI Hot Plug Controller Intersil Corporation
Intersil Corporation
HIP1011B PCI Hot Plug Controller Intersil Corporation
Intersil Corporation
HIP1011D Dual PCI Hot Plug Controller Intersil Corporation
Intersil Corporation

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche