HIP0080AM Datasheet PDF - Intersil Corporation
| Part Number | HIP0080AM | |
| Description | Quad Inverting Power Drivers with Serial Diagnostic Interface | |
| Manufacturers | Intersil Corporation | |
| Logo |  |
|
|
There is a preview and HIP0080AM download ( pdf file ) link at the bottom of this page. Total 15 Pages | ||
Preview 1 page No Preview Available !
HIP0080, HIP0081
September 1998
File Number 3018.4
Quad Inverting Power Drivers with Serial
Diagnostic Interface
HIP0080, HIP0081The HIP0080/0081 Quad Power Drivers
contain four individually protected NDMOS power output
transistor switches to drive inductive and resistive loads
such as: relays, solenoids, injectors, AC and DC motors,
heaters and incandescent lamp displays. The 4 Power
Drivers are low-side switches driven by CMOS logic input
control stages. Each Output Power Driver is protected
against over-current, over-temperature and over-voltage.
An internal drain-to-gate zener diode provides the clamping
protection for over-voltage. Diagnostic circuits provide
ground short, supply short, open load and thermal overload
detection for each of the 4 output stages. Each of the 4
input drivers and their respective diagnostic filters are
controlled by one ENABLE input.
HIP0080, HIP0081The inputs are CMOS logic compatible
and individually control the output drivers with an active
high state for turn-on. All other control inputs are active
high with the exception of the Chip Select (CS) which is
active low. The DATAIN (DI) and DATAOUT (DO) are
positive logic and the Clock (CLK) input for the Serial
Interface is active on the rising edge of the CLK pulse. All
Inputs except the HIP0080 ENABLE have a nominal level
of hysteresis. IN1, IN2, IN3, IN4 and ENABLE have pull-
down resistors of approximately 100kΩ. This switches off
any channel that has an unterminated input.
HIP0080, HIP0081Filters are used on the outputs of the
fault sensing comparators to avoid the detection of short
duration transient spikes. The on-chip oscillator is used to
clock an internal shift register in each filter. If the fault
condition is longer than a preset number of clock cycles,
the fault condition is recognized and the respective bit is
set in the diagnostic register. No filter is used in the
thermal-overload feedback circuit and the bit is set when
thermal shutdown occurs.
HIP0080, HIP0081For normal operating conditions, a
Reset turns off all outputs when the VCC level drops below
3.5V. The internal bandgap and bias supply function
includes a 5V regulated supply for the low voltage signal
and logic circuits.
Features
• Low Side Power MOSFET Output Drivers
• Output Driver Protection
- Over-Current Shutdown
- Over-Temperature Shutdown with Hysteresis
- Over-Voltage Internal Clamp
• HIP0081 Output Current Switching Capability:
- Each Output, IOUT . . . . . . . . . . . . . . . . . . . . . . 2.2A DC
- All Outputs ON, Equal IOUT . . . . . . . . . . . . . . . . 6A DC
- All Outputs ON, Equal IOUT . . . . . . . . . . 8A PK, 500ms
• HIP0080 Output Current Switching Capability:
- Each Output, IOUT . . . . . . . . . . . . . . . . . . . . . . 1.3A DC
- All Outputs ON, Unequal IOUT . . . . . . . . . . . . . . 3A DC
- All Outputs ON, Unequal IOUT . . . . . . . . 4A PK, 500ms
• HIP0080 - Low Idle Current Shutdown Mode
• Regulated Interface for 5V CMOS Logic Inputs
• Open Drain High Z DATAOUT
• Fault Mode Output for Shorts, Opens and Over-Temperature
• 16-Bit Serial Diagnostic Register
• SPI Bus Compatible Data Readout
• HIP0081 - Low θJC Power Package . . . . . . . . . . . . 3oC/W
• -40oC to 125oC Operating Temperature Range
Applications
• Drivers For:
- Solenoids
- Relays
- Power Output
- Lamps
- Injectors
- Steppers
- Motors
- Displays
• System Use:
- Automotive
- Appliances
- Industrial
- Robotics
Ordering Information
PART NUMBER
HIP0081AS1
HIP0081AS2
HIP0080AM
TEMP.
RANGE (oC)
PACKAGE
-40 to 125 15 Ld SIP
-40 to 125 15 Ld SIP
-40 to 125 28 Ld PLCC
PKG.
NO.
Z15.05A
Z15.05B
N28.45
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
|
| |
 
HIP0080, HIP0081
Electrical Specifications VCC = 5.5V to 25V ±5%, TA = -40oC to 125oC, Unless Otherwise Specified (Continued)
HIP0080
HIP0081
PARAMETER
SYMBOL
TEST CONDITIONS
MIN TYP MAX MIN TYP MAX UNITS
HIP0080 Output Leakage
Current
IOFFLK Inputs Low, Each VOUT = 25V,
ENABLE Low
- 1.0 10 - - - µA
Over-Voltage Clamp Range
Current Short Circuit Prot.
Short Circuit Det. Delay
Output ON-OFF Voltage
Ramp Rate
VCLAMP IN Inputs Low (Outputs OFF),
IOUT = 40mA
IOUT(SC) Note 2
tSCDLY
Resistive Load
27 - 43 73 - 89 V
1.3 -
-6
- 10
3 2.2 - 4.8 A
- - 6 - µs
- - 10 - V/µs
Turn-On Delay
Turn-Off Delay
SUPPLY
tPHL
tPLH
VCC = 14V, RLOAD = 14Ω
VCC = 14V, RLOAD = 14Ω
- - 8 - - 8 µs
- - 8 - - 8 µs
Power Supply Current
Power Supply Reset Active
Shut-Down Current Mode
INPUTS
ICC
VCC_RST
TA = 25oC to TA = 125oC
TA = -40oC
ISHTDN Enable Low
- 20 30 - 20 30 mA
3 - 43 - 4 V
2.7 -
4 2.7
-
4
V
- 130 200 - - - µA
Low-Level Input Voltage
High-Level Input Voltage
Input Hysteresis Threshold
Input Pull-Down
Resistance
VIL
VIH
VIN_HYS (N.A. to HIP0080 ENABLE)
RPD IN1, IN2, IN3, IN4 and ENABLE
- - 1- - 1
3.5 -
- 3.5
-
-
0.85 - 2.25 0.85 - 2.25
50 100 200 50 100 200
V
V
V
kΩ
DATAOUT (Open Drain)
Leakage Current
IDO_LEAK VDO = 7V, DO OFF (High)
Logic Low Output Voltage
VOL IDO = 1.6mA, DO ON (Low)
Max. Logic Low Current
IOH VDO = 4.5V, DO ON
Oscillator Frequency
fOSC
Serial Interface Clock Freq.
fCLK Note 5
DIAGNOSTIC AND PROTECTION
Over-Temperature
Shutdown Threshold
Shutdown Temperature Hys-
teresis
- - 10 - - 10 µA
- - 0.4 - - 0.4 V
1.6 -
- 1.6
-
- mA
- 500 -
- 500 - kHz
- - 2 - - 2 MHz
150 165
- 15
- 150 165
- - 15
-
-
oC
oC
Output Short-to-GND
Threshold
Short-to-GND Hysteresis
Open-Load Resistance for
No-Load Warning
VCC = 5.5V to 16V
VCC = 5.5V to 16V
VCC = 5.5V to 16V
- 0.24x -
VCC
- 0.02x -
VCC
5 - 25
- 0.24x -
VCC
- 0.02x -
VCC
5 - 25
V
V
kΩ
Filter Delay Time for O.L. or
Short-to-GND
- 12 - - 12 - µs
NOTE:
5. The maximum Serial Clock Frequency may be limited by the time constant of the external load network at the DATAOUT pin.
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for HIP0080AM electronic component. |
| Information | Total 15 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ HIP0080AM.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| HIP0080AM | The function is Quad Inverting Power Drivers with Serial Diagnostic Interface. Intersil Corporation | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
HIP0
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||