DataSheetWiki


SF2183E fiches techniques PDF

RF Monolithics - SAW Filter

Numéro de référence SF2183E
Description SAW Filter
Fabricant RF Monolithics 
Logo RF Monolithics 





1 Page

No Preview Available !





SF2183E fiche technique
SF2183E
• Surface Mount 3.0 x 3.0 mm Package
• Complies with Directive 2002/95/EC (RoHS)
Absolute Maximum Ratings
Rating
Input Power Level
DC Voltage on any Non-ground Terminal
Operating Temperature Range
Component Storage Temperature Range
Storage Temperature Range in Tape and Reel
Maximum Soldering Profile, 5 cycles/ 10 seconds maximum
Pb
Value
10
6
-40 to +85
-40 to +125
-40 to +85
265
Units
dBm
V
°C
°C
°C
°C
400.00 MHz
SAW Filter
Electrical Characteristics
Characteristic
Center Frequency
Minimum Insertion Loss
Passband Attenuation Relative to ILMIN, 399.875 to 400.125 MHz
Stopband Attenuation Referenced to ILMIN:
10.0 to 370.0 MHz
370.0 to 390.0 MHz
390.0 to 398.8 MHz
401.0 to 409.0 MHz
409.0 to 414.0 MHz
414.0 to 800.0 MHz
800.0 to 2500.0 MHz
Input Impedance
Output Impedance
Case Style
Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator
Standard Reel Quantity
Reel Size 7 Inch
Reel Size 13 Inch
Electrical Connections
Connection
Input
Output
Case Ground
Terminals
2
5
All others
Sym
fC
ILMIN
Notes
Min
Typ
400.00
3.0
0.7
SM3030-6
Max
4.0
3.0
www.DataSheet.net/
ZS
ZL
50 56
42 46
22 25
10 22
30 40
42 50
45 55
865 || 2 pF
865 || 2 pF
SM3030-6 3.0 x 3.0 mm Nominal Footprint
871, YWWS
500 Pieces/Reel
3000 Pieces/Reel
O u tp u t
5 0 o h m M a tc h in g N e tw o r k
61
73 nH
6 .8 p F
52
43
73 nH
6 .8 p F
S F2183E
(b o tto m v ie w )
In p u t
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
Notes:
Units
MHz
dB
dB
1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance
matching to 50 and measured with 50 network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external
impedance matching design. See Application Note No. 42 for details.
4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."
5. The design, manufacturing process, and specifications of this filter are subject to change.
6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port
2, so that the filter must always be installed in one direction per the circuit design.
7. US and international patents may apply.
8. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc.
www.RFM.com E-mail: [email protected]
©2009-2010 by RF Monolithics, Inc.
Page 1 of 4
SF2183E - 7/19/10
Datasheet pdf - http://www.DataSheet4U.co.kr/

PagesPages 4
Télécharger [ SF2183E ]


Fiche technique recommandé

No Description détaillée Fabricant
SF2183E SAW Filter RF Monolithics
RF Monolithics

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche