DataSheetWiki


SF2178A fiches techniques PDF

RF Monolithics - SAW Filter

Numéro de référence SF2178A
Description SAW Filter
Fabricant RF Monolithics 
Logo RF Monolithics 





1 Page

No Preview Available !





SF2178A fiche technique
• Precision IF SAW Filter
• Hermetic 13.3 x 6.5 mm Surface-mount Case
• Complies with Directive 2002/95/EC (RoHS)
Absolute Maximum Ratings
Pb
Rating
Maximum Incident Power in Passband
Maximum DC Voltage Between any 2 Terminals
Storage Temperature Range
Suitable for Lead-free Soldering - Maximum Soldering Profile
Value
Units
+10 dBm
30 VDC
-40 to +85
°C
260°C for 30 s
SF2178A
168 MHz
SAW Filter
SM13365-12
Electrical Characteristics
Characteristic
Center Frequency
1 dB Bandwidth
3 dB Bandwidth
Upper -35 dB Band Edge
Lower -35 dB Band Edge
Insertion Loss
Passband Ripple (p-p)
Absolute Group Delay
Group delay ripple (p-p)
Operating Temperature
Source Impedance
VSWR to Source (Matching Network)
Load Impedance
VSWR to Load (Matching Network)
Frequency Temperature Coefficient
Impedance Matching to 50 Unbalanced
Case Style
Lid Symbolization (YY = year, WW = week)
158 to 178 MHz
168 MHz
158 to 178 MHz
Sym
fC
BW1
BW3
IL
Notes
1
1
1
1
1
1
www.DataSheet.net/
1, 2, 3
1
159.5 to 168.5 MHz
159.5 to 168.5 MHz
Min
20.0
154
-40
Typ
168
20.9
22.4
181.7
155.1
12.2
0.76
0.85
54
50
2.3
50
2.2
-72
Max
182.0
13.5
1.0
1
160
+85
External L-C
SM13365-12 13.3 x 6.5 mm Nominal Footprint
RFM SF2178A YYWW
Units
MHz
MHz
MHz
MHz
MHz
dB
dB
µs
ns
°C
ohm
ohm
ppm/°C
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
Notes:
1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance
matching to 50 and measured with 50 network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external
impedance matching design. See Application Note No. 42 for details.
4. Part to part absolute delay measurement records the absolute delay mean across 1 dB passband.
5. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes.”
6. The design, manufacturing process, and specifications of this filter are subject to change.
7. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port
2, so that the filter must always be installed in one direction per the circuit design.
8. US and international patents may apply.
www.RFM.com E-mail: [email protected]
©2008 by RF Monolithics, Inc.
Page 1 of 5
SF2178A - 7/7/09
Datasheet pdf - http://www.DataSheet4U.co.kr/

PagesPages 5
Télécharger [ SF2178A ]


Fiche technique recommandé

No Description détaillée Fabricant
SF2178A SAW Filter RF Monolithics
RF Monolithics

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche