|
|
Número de pieza | SF2135A | |
Descripción | SAW Filter | |
Fabricantes | RF Monolithics | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de SF2135A (archivo pdf) en la parte inferior de esta página. Total 4 Páginas | ||
No Preview Available ! • Designed for Wide Channel IF Filtering
• Low Insertion Loss
• Hermetic 13.3 x 6.5 mm Surface-mount Case
• Balanced or Single-ended Input and Output
• Complies with Directive 2002/95/EC (RoHS)
Pb
Absolute Maximum Ratings
Rating
Maximum Incident Power in Passband
Maximum DC Voltage Between any Two Terminals
Storage Temperature Range
Suitable for Lead-free Soldering - Maximum Soldering Profile
Value
Units
+13 dBm
30 VDC
-40 to +85
°C
260 °C for 30 s
SF2135A
96.0 MHz
SAW Filter
SMP-53
Electrical Characteristics
Characteristic
Center Frequency
1 dB Bandwidth
Insertion Loss
Relative Attenuation
Passband Amplitude Ripple
Group Delay Ripple
Operating Temperature
Terminating Source Impedance
Terminating Load Impedance
Impedance Matching to 50 Ω Unbalanced
Case Style
Lid Symbolization (YY = year, WW = week)
91 to 94.5 MHz
97.5 to 98.5 MHz
10 to 60 MHz
76.8 MHz
132 to135 MHz
135 to 1000 MHz
95.2 to 96.8 MHz
95.2 to 96.8 MHz
Sym
fC
BW1
IL
Notes
1
1, 2,3
www.DataSheet.net/
1, 2, 3
1
Min
1.56
6
6
55
55
55
35
-30
Typ
96.0
1.80
11.8
9.5
11.5
72
72
74
58
0.9
62
50
50
Max
15.0
1.2
100
+85
External L-C
SMP-53 13.3 x 6.5 mm Nominal Footprint
RFM SF2135A YYWW
Units
MHz
MHz
dB
dB
dB
dB
dB
dBP-P
nsP-P
°C
ohm
ohm
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
Notes:
1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance
matching to 50 Ω and measured with 50 Ω network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external
impedance matching design. See Application Note No. 42 for details.
4. Part to part absolute delay measurement records the absolute delay mean across 1 dB passband.
5. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes.”
6. The design, manufacturing process, and specifications of this filter are subject to change.
7. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port
2, so that the filter must always be installed in one direction per the circuit design.
8. US and international patents may apply.
www.RFM.com E-mail: [email protected]
©2009 by RF Monolithics, Inc.
Page 1 of 4
SF2135A - 7/9/09
Datasheet pdf - http://www.DataSheet4U.co.kr/
1 page |
Páginas | Total 4 Páginas | |
PDF Descargar | [ Datasheet SF2135A.PDF ] |
Número de pieza | Descripción | Fabricantes |
SF2135A | SAW Filter | RF Monolithics |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |