DataSheetWiki


SF2027B fiches techniques PDF

RF Monolithics - SAW Filter

Numéro de référence SF2027B
Description SAW Filter
Fabricant RF Monolithics 
Logo RF Monolithics 





1 Page

No Preview Available !





SF2027B fiche technique
®
• GSM BTS Receiver IF Applications
• Small Size
• Hermetic 13.3 X 6.5 mm Surface Mount Case
SF2027B
199.0 MHz
SAW Filter
Input power Level short test
standard operation, max
Max DC Voltage between any 2 terminals
Input: possible for balanced and unbalanced operation (TBD)
Output: Balanced
External matching to 50 or 200 ohms
+18 dBm
+10 dBm
10V
SMP-53-S
Electrical Characteristics
Characteristic
Nominal Frequency
Insertion Loss
(including matching to 200 ohms)
Group Delay Ripple, peak - peak (198.9 .. 199.1 MHz)
Amplitude Ripple, peak - peak
(198.9 .. 199.1 MHz)
Relative attenuation fn - 100 kHz .. fn +100 kHz (passband)
fn - 300 kHz, fn +300 kHz
fn - 500 kHz, fn +500 kHz
fn - 600 kHz, fn +600 kHz
<fn - 700 kHz,> fn +700 kHz
Sym
fN
IL
www.DataSheet.net/
Notes
1
Min
Typ
199.0
< 7.0
< 700
< 1.0
< 0.7
> 10
> 27
> 36
> 45
Max
Case Style
Lid Symbolization (Y=year, WW=week, S=shift) See note 4
SMP-53-S 13.3 X 6.5 mm Nominal Footprint
RFM SF2027B YWWS
Units
MHz
dB
ns
dB
dB
dB
dB
dB
Notes:
1. Unless noted otherwise, all specifications apply over the operating temperature
range with filter soldered to the specified demonstration board with impedance
matching to 50 and measured with 50 network analyzer. A dB offset exists
for RFM because of the loss introduced by using transformers on the Input and
Output.
2. Rejection is measured as attenuation below the minimum IL point in the pass-
band. Rejection in final user application is dependent on PCB layout and exter-
nal impedance matching design. See Application Note No. 42 for details.
3. "LRIP" or "L" after the part number indicates "low rate initial production" and
"ENG" or "E" indicates "engineering prototypes."
4. The design, manufacturing process, and specifications of this filter are subject
to change.
5. Either Port 1 or Port 2 may be used for either input or output in the design.
However, impedances and impedance matching may vary between Port 1 and
Port 2, so that the filter must always be installed in one direction per the circuit
design.
6. US and international patents may apply.
7. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of
RF Monolithics, Inc.
8. ©Copyright 1999, RF Monolithics Inc.
9. Electrostatic Sensitive Device. Observe precautions for handling.
RF Monolithics, Inc. Phone: (972) 233-2903
Fax: (972) 387-8148
RFM Europe
Phone: 44 1963 251383
Fax: 44 1963 251510
©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
http://www.rfm.com
SF2027B-041403
Page 1 of 4
Datasheet pdf - http://www.DataSheet4U.co.kr/

PagesPages 4
Télécharger [ SF2027B ]


Fiche technique recommandé

No Description détaillée Fabricant
SF2027B SAW Filter RF Monolithics
RF Monolithics

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche