DataSheetWiki


SF1146B fiches techniques PDF

RF Monolithics - SAW Filter

Numéro de référence SF1146B
Description SAW Filter
Fabricant RF Monolithics 
Logo RF Monolithics 





1 Page

No Preview Available !





SF1146B fiche technique
®
• Low Insertion Loss
• 5.0 X 7.0 mm Surface-Mount Case
• Complies with Directive 2002/95/EC (RoHS)
SF1146B
499.25 MHz
SAW Filter
Absolute Maximum Ratings
Rating
Maximum Incident Power in Passband
Max. DC voltage between any 2 terminals
Storage Temperature Range
Suitable for lead-free soldering - Max Soldering Profile
Value
Units
+10 dBm
30 VDC
-40 to +85
°C
260°C for 30 s
SMP-03
Electrical Characteristics
Characteristic
Nominal Center Frequency
Passband
Insertion Loss at fc
1.5 dB Passband
Rejection
fc±1.5 MHz
fc±6.0 MHz
fc±50 MHz
Operating Temperature Range
Differential Input and Output Impedance after matching
Case Style
Lid Symbolization (YY=year, WW=week, S=shift) See note 4
Sym
fC
IL
BW1
Notes
1
1, 2
1, 2, 3
TA 1
www.DataSheet.net/
6
Min Typ Max Units
499.25
MHz
3.5 dB
±15 kHz
5
20 dB
50
-40 +85 °C
50 ohms
SMP-03 7 x 5 mm Nominal Footprint
RFM SF1146B YYWWS
Electrical Connections
Connection
Port 1 Hot
Port 1 Ground Return
Port 2 Hot
Port 2 Ground Return
Case Ground
Terminals
10
1
5
6
All Others
Notes:
1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to
50 and measured with 50 network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance
matching design. See Application Note No. 42 for details.
4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."
5. The design, manufacturing process, and specifications of this filter are subject to change.
6. Tape and Reel Standard ANSI / EIA 481.
7. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that
the filter must always be installed in one direction per the circuit design.
8. US and international patents may apply.
9. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc.
10. ©Copyright 1999, RF Monolithics Inc.
11. Electrostatic Sensitive Device. Observe precautions for handling.
RF Monolithics, Inc. Phone: (972) 233-2903
Fax: (972) 387-8148
RFM Europe
Phone: 44 1963 251383
Fax: 44 1963 251510
©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
http://www.rfm.com
SF1146B-040407
Page 1 of 3
Datasheet pdf - http://www.DataSheet4U.co.kr/

PagesPages 3
Télécharger [ SF1146B ]


Fiche technique recommandé

No Description détaillée Fabricant
SF1146B SAW Filter RF Monolithics
RF Monolithics

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche