DataSheetWiki


L6360 fiches techniques PDF

STMicroelectronics - IO-Link communication master transceiver IC

Numéro de référence L6360
Description IO-Link communication master transceiver IC
Fabricant STMicroelectronics 
Logo STMicroelectronics 





1 Page

No Preview Available !





L6360 fiche technique
L6360
IO-Link communication master transceiver IC
Features
Supply voltage from 18 to 32.5 V
Programmable output stages: high-side,
low-side or push-pull (< 2 Ω)
Up to 500 mA L+ protected high-side driver
Supports COM1, COM2 and COM3 mode
Additional IEC61131-2 type-1 input
Short-circuit and overcurrent output protection
through current limitation and programmable
cutoff current
3.3 V / 5 V, 50 mA linear regulator
5 mA IO-Link digital input
Fast mode I2C for IC control, configuration and
diagnostic
Diagnostic dual LED sequence generator and
driver
5 V and 3.3 V compatible I/Os
Overvoltage protection (> 36 V)
Overtemperature protection
ESD protection
Miniaturized: VFQFPN-26L
3.5 x 5 x 1 mm package
Applications
Industrial sensors
Factory automation
Process control
Description
The L6360 is a monolithic IO-Link master port
compliant with PHY2 (3 wires) supporting COM1
(4.8 kbaud), COM2 (38.4 kbaud) and COM3
(230.4 kbaud) modes.
The C/QO output stage is programmable: high-
side, low-side or push-pull; also cutoff current,
Datasheet production data
VFQFPN-26L 3.5 x 5 x 1 mm
cutoff current delay time, and restart delay are
programmable.
Cutoff current and cutoff current delay time,
combined with thermal shutdown and automatic
restart protect the device against overload and
short-circuit.
C/QO and L+ output stages are able to drive
resistive, inductive and capacitive loads. Inductive
loads up to 10 mJ can be driven.
Supplywww.DataSheet.net/ voltage is monitored and low voltage
conditions are detected.
The L6360 transfers, through the PHY2(C/QO
pin), data received from a host microcontroller
through the USART (IN C/QO pin), or to the
USART (OUT C/QI pin) data received from PHY2
(C/QI pin).
To enable full IC control, configuration and
monitoring (i.e. fault conditions stored in the
status register), the communication between the
system microcontroller and the L6360 is based on
a Fast mode 2-wire I2C.
The L6360 has nine registers to manage the
programmable parameters and the status of the
IC.
Monitored fault conditions are: L+ line,
overtemperature, C/Q overload, linear regulator
undervoltage, and parity check.
Internal LED driver circuitries, in open drain
configuration, provide two programmable
sequences to drive two LEDs.
March 2012
This is information on a product in full production.
Doc ID 022817 Rev 2
1/65
www.st.com
65
Datasheet pdf - http://www.DataSheet4U.co.kr/

PagesPages 65
Télécharger [ L6360 ]


Fiche technique recommandé

No Description détaillée Fabricant
L6360 IO-Link communication master transceiver IC STMicroelectronics
STMicroelectronics
L6362 Fully integrated device transceiver IC STMicroelectronics
STMicroelectronics
L6362A IO-Link communication transceiver device IC STMicroelectronics
STMicroelectronics
L6363 PRML READ/WRITE CHANNEL STMicroelectronics
STMicroelectronics

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche