|
|
PDF LTN160AT02 Data sheet ( Hoja de datos )
| Número de pieza | LTN160AT02 | |
| Descripción | Display Module | |
| Fabricantes | Samsung | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LTN160AT02 (archivo pdf) en la parte inferior de esta página. Total 29 Páginas | ||
|
No Preview Available !
Approval
TO :
DATE : Oct. 06, 2008.
SSAAMMSSUUNNGGTTFFTT-L-LCCDD
MMOODDEELL NNOO.. :: LLTTNN116600AATT0022
NOTE : Extension code [ -002 ]
www.DataSheet.net/
→ LTN160AT02-002
Surface type [ Anti-Glare ]
Any Modification of Spec is not allowed without SEC’ permission
APPROVED BY :
PREPARED BY :
Samsung Secret
Application Engineering part.
Mobile Division
Samsung Electronics Co., Ltd.
Doc.No.
LTN160AT02
Rev.No
04-A00-G-080804
Page 1 / 30
Datasheet pdf - http://www.DataSheet4U.co.kr/
1 page  
1.2 ELECTRICAL ABSOLUTE RATINGS
Approval
(1) TFT LCD MODULE
Item
Power Supply Voltage
Logic Input Voltage
Note (1) Within Ta (25 ± 2 °C )
Symbol
VDD
VIN
Min.
VDD - 0.3
VDD - 0.3
VDD =3.3V, VSS = GND = 0V
Max.
Unit Note
VDD + 0.3
V
(1)
VDD + 0.3
V
(1)
(2) BACK-LIGHT UNIT
Item
Lamp Current
Lamp frequency
Symbol
IL
FL
Min.
3.0
50
Max.
7.0
80
Ta = 25 ± 2 °C
Unit Note
mArms
(1)
kHz (1)
Note 1) Permanent damage to the device may occur if maximum values are exceeded
Functional operation should be restricted to the conditions described under normal operating conditions.
www.DataSheet.net/
Samsung Secret
Doc.No. LTN160AT02
Rev.No
04-A00-G-080804
Page 5 / 30
Datasheet pdf - http://www.DataSheet4U.co.kr/
5 Page 
3.2 BACK-LIGHT UNIT
Approval
The backlight system is an edge-lighting type with a single CCFL ( Cold Cathode Fluorescent Lamp ).
The characteristics of a single lamp are shown in the following tables.
- INVERTER : (SEM SIC 130T)
Ta= 25 ± 2 °C
Item
Symbol
Min.
Typ.
Max.
Unit
Note
Lamp Current
IL 3.0 6.0 6.5 mArms
(1)
Lamp Voltage
VL
-
705
-
Vrms
IL = 6.0mA
Frequency
fL 50 60 65 KHz
(2)
Power Consumption
PL
-
4.5
(3)
W
IL = 6.0mA
Operating Life Time Hr 10.000
-
- Hour
(4)
Startup Voltage
VS
-
1230
Vrms
25°C, (5)
-
1480
Vrms
0°C, (5)
Lamp Startup Time
- - 1.0 sec
(5)
Note) The waveform of the inverter output voltage must be area symmetric and the design of the
inverter must have specifications for the modularized lamp.
The performance of the backlight, for example life time or brightness, is much influenced by the
characteristics of the DC-AC inverter for the lamp. So all the parameters of an inverter should be carefully
designed so as not to produce too much leakage current from high-voltage output of the inverter.
When you design or order the inverter, please make sure that a poor lighting caused by the mismatch of
the backlight and the inverter(miss lighting, flicker, etc.) never occur. When you confirm it, the module
should be operated in the same condition as it is installed in your instrument.
www.DataSheet.net/
Note (1) Lamp current is measured with a high frequency current meter as shown below.
LCD
MODULE
HOT : Pink
1
COLD : White
2A
INVERTER
(2) Lamp frequency may produce interference with horizontal synchronous frequency and this
may cause line flow on the display. Therefore lamp frequency should be detached from the
horizontal synchronous frequency and its harmonics as far as possible in order to avoid interference.
(3) Refer to IL ×VL to calculate.
(4) Life time (Hr) of a lamp can be defined as the time in which it continues to operate under the
condition Ta= 25 ± 2 °C and IL = 6.0 mArms until one of the following event occurs.
1. When the brightness becomes 50% or lower than the original.
2. When the Effective ignition length becomes 80% or lower than the original value.
(Effective ignition length is defined as an area that has less than 70% brightness compared to
the brightness in the center point.)
(5) The inverter open voltage - this voltage should be measured after ballast capacitor- have to be larger
than the lamp startup voltage, otherwise backlight may has blinking for a moment after turns on
or not be turned on.
If an inverter has shutdown function it should keep its open voltage for longer than 1 second
even if lamp connector open.
Samsung Secret
Doc.No.
LTN160AT02
Rev.No
04-A00-G-080804
Page 11 / 30
Datasheet pdf - http://www.DataSheet4U.co.kr/
11 Page | ||
| Páginas | Total 29 Páginas | |
| PDF Descargar | [ Datasheet LTN160AT02.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LTN160AT01-A02 | Display Module | Samsung |
| LTN160AT02 | Display Module | Samsung |
| LTN160AT03-0 | TFT LCD | Samsung |
| LTN160AT06-B01 | TFT LCD | Samsung |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |