|
|
Número de pieza | B150PG03-V0 | |
Descripción | LCD Module | |
Fabricantes | AUO | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de B150PG03-V0 (archivo pdf) en la parte inferior de esta página. Total 26 Páginas | ||
No Preview Available ! Product Functional Specification
15 inch SXGA+ Color TFT LCD Module
Model Name: B150PG03 V0
( ) Preliminary Specification
( ) Final Specification
www.DataSheet.co.kr
Note: This Specification is subject to change without notice.
(C) Copyright AU Optronics, Inc.
April, 2004 All Rights Reserved.
No Reproduction and Redistribution Allowed.
B150PG03 V0 Ver.02
1/26
Datasheet pdf - http://www.DataSheet4U.net/
1 page 1.0 Handing Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure
human earth when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was
taken out from the container, do not press the center of the CCFL Reflector edge.
Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT
Module may be damaged.
10)At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor
tilt the Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
www.DataSheet.co.kr
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be damaged.
12)Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow
local ordinances or regulations for disposal.
13)Small amount of materials having no flammability grade is used in the LCD module. The
LCD module should be supplied by power complied with requirements of Limited Power
Source(2.11, IEC60950 or UL1950), or be applied exemption.
14)The LCD module is designed so that the CFL in it is supplied by Limited Current Circuit(2.4,
IEC60950 or UL1950). Do not connect the CFL in Hazardous Voltage Circuit.
(C) Copyright AU Optronics, Inc.
April, 2004 All Rights Reserved.
No Reproduction and Redistribution Allowed.
B150PG03 V0 Ver.02
5/26
Datasheet pdf - http://www.DataSheet4U.net/
5 Page Note 1: 5 points position (Display area : 304.5mm x 228.375mm)
W
W/4 W/4 W/4
W/4
H/4
H/4
H
H/4
H/4
12
3
45
www.DataSheet.co.kr
(C) Copyright AU Optronics, Inc.
April, 2004 All Rights Reserved.
No Reproduction and Redistribution Allowed.
B150PG03 V0 Ver.02
11/26
Datasheet pdf - http://www.DataSheet4U.net/
11 Page |
Páginas | Total 26 Páginas | |
PDF Descargar | [ Datasheet B150PG03-V0.PDF ] |
Número de pieza | Descripción | Fabricantes |
B150PG03-V0 | LCD Module | AUO |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |