DF-G1 Datasheet PDF - Banner Engineering
| Part Number | DF-G1 | |
| Description | Expert Fiber Amplifier Install Sheet | |
| Manufacturers | Banner Engineering | |
| Logo |  |
|
|
There is a preview and DF-G1 download ( pdf file ) link at the bottom of this page. Total 10 Pages | ||
Preview 1 page No Preview Available !
www.DataSheet.co.kr
DF-G1 - Expert Fiber Amplifier Install Sheet
Advanced sensor with dual digital displays for use with plastic and glass fiber optic assemblies
For the latest technical information about this product, including specifications, dimensions, and wiring, see www.BannerEngineering.com
Overview
Figure 1. DF-G1 Model Features
1 Output LED
2 LO/DO Switch
3 RUN/PRG/ADJ Mode Switch
4 Lever Action Fiber Clamp
5 Red Signal Level
6 Green Threshold
7 +/SET/- Rocker Button
Models
Model
DF-G1-NS-2M
DF-G1-PS-2M
DF-G1-NS-Q3
DF-G1-PS-Q3
DF-G1-NS-Q7
DF-G1-PS-Q7
Outputs
Single NPN
Single PNP
Single NPN
Single PNP
Single NPN
Single PNP
Connector*
2 m (6.5') cable, 4-wire
* Cordset Options: A model with a QD connector requires a
mating cordset. For 9 m cable, change the suffix 2M to 9M in
the 2 m model number (example, DF-G1-NS-9M). For M12
Euro QD pigtail change the suffix 2M to Q5 in the 2 m model
number (example, DF-G1-NS-Q5).
150 mm (6") PVC pigtail, M8 Pico QD
connector, 4-pin
Integral M8 Pico QD connector, 4-pin
WARNING: Not To Be Used for Personnel Protection
Never use this product as a sensing device for personnel protection. Doing so could lead to serious injury or death. This
product does NOT include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor
failure or malfunction can cause either an energized or de-energized sensor output condition.
Hookups
NPN Models
For cable options, see http://www.bannerengineering.com
PNP Models
Key
1
4
1 = Brown
2 = White
3 = Blue
4 = Black
2
3
P/N 161275 Rev. A
1/6/2012
0 161275 2
Datasheet pdf - http://www.DataSheet4U.net/
|
| |
 
www.DataSheet.co.kr
DF-G1 - Expert Fiber Amplifier Install Sheet
Dynamic TEACH
• Teaches on-the-fly
• Establishes a single switching threshold
• Threshold can be adjusted using “+” and “-” rocker button (Manual Adjust)
Dynamic TEACH is best used when a machine or process may not be stopped for teaching. The sensor learns during actual sensing conditions, taking multiple samples of
the light and dark conditions and automatically setting the threshold at the optimum level (see Figure below).
The output ON and OFF conditions can be reversed using the LO/DO switch (see LO/DO Switch in Top Panel Interface on page 2).
Dynamic TEACH and Manual Adjust
• Moves switching threshold value up or down to make adjustments
• Slide Mode switch to ADJ to enter Adjust mode
• Press “+” to increase; press “-” to decrease
• GREEN display shows the switching threshold value
• 2 seconds after adjustment, GREEN display will flash 3 times to confirm
• Slide Mode switch to RUN to complete operation
Darkest Taught
Condition
Lightest Taught
Condition
Sensor positions
threshold midway
between taught conditions
Output OFF
Output ON
Remember: Manual adjustments are disabled
when Auto Thresholds are ON
Darkest
(no signal)
Position
adjusted by
Manual Adjust
Figure 3. Dynamic TEACH (Light Operate shown)
Most Light
(saturated
signal)
SET Button
0.04 seconds < "Click" < 0.8 seconds
Remote Input
0.04 seconds < T < 0.8 seconds
Result
Note: TEACH Selection must be programmed to dYn tcH (see Program Mode on page 3 )
Enter Adjust
Mode
• Set Mode switch to ADJ
Enter Dynamic
TEACH
• Click the SET rocker button
No action required; sensor is ready for Display: Red - Signal Level; Green -
Dynamic TEACH method
Threshold
• Single-pulse remote input
T
Display: Flashes "dYn tch" then
holds on "1234 dYn"
Present ON
and OFF Con-
ditions
Exit Dynamic
TEACH
Return to RUN
Mode
• Present ON and OFF conditions
• Present ON and OFF conditions Display: Red - Signal Level; Green -
Threshold
• Click the SET rocker button
• Move Mode switch to RUN
• Single-pulse remote input
T
No action required; sensor returns to
RUN mode automatically
TEACH Accepted
Displays alternate "PASS" with % Min-
imum Difference*, Sensor returns to
Adjust mode
TEACH Unacceptable
Displays alternate "FAIL" with % Mini-
mum Difference*, Sensor returns to
Adjust mode
Display: Red - Signal Level; Green -
Threshold
* See Troubleshooting on page 10 for more explanation of the % Minimum Difference displayed after the Dynamic TEACH method
P/N 161275 Rev. A
www.bannerengineering.com - tel: 763-544-3164
5
Datasheet pdf - http://www.DataSheet4U.net/
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for DF-G1 electronic component. |
| Information | Total 10 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ DF-G1.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| DF-G1 | The function is Expert Dual Display Fiber Amplifier Manual. Banner Engineering | |
| DF-G1 | The function is Expert Fiber Amplifier Install Sheet. Banner Engineering | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
DF-G
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||