DataSheetWiki


LCM1210R2 fiches techniques PDF

ETC - Molded Chip Inductor

Numéro de référence LCM1210R2
Description Molded Chip Inductor
Fabricant ETC 
Logo ETC 





1 Page

No Preview Available !





LCM1210R2 fiche technique
wwwD. aatSheec.tok.r
LCM1210R2 Molded
Chip Inductor
FEATURES
Small molded chip inductor
Special ferrite core ensures stable inductance against
temperature humidity
Broad inductance range
High Q
Highly reliable
Excellent for flow, re-flow soldering, and soldering iron
.126" ± .012"
3.20mm ± .3
.098" ± .012"
2.50mm ± .3
.086" ± .012"
2.20mm ± .3
.020" ± .008"
.5 mm
.067" ±.003"
1.7 mm
APPLICATIONS
TV's, VCR's, and audio equipment
Disk drives and other computer periferals
Personal computers
Electronic control boards for automobiles
Telecommunication devices
CHARACTERISTICS
INDUCTANCE RANGE .01 µH to 330 µH
TOLERANCE 10% over entire range. 5% available upon request
CURRENT RATING Based on current flow and temperature rise of 20°C maximum at 80°C ambient temperature.
TESTING PROCEDURE Inductance, Q, and SRF measured by HP4191A Impedance Analyzer with 16092A Test Clip at specified
frequency. DCR measured with digital milliohms meter.
DIELECTRIC STRENGTH 1000 volts DC between both terminals and package of coil for 5 seconds.
SOLDERABILITY 95% of the terminal is covered with solder. Please refer to page 2 for soldering recommendations.
SOLDERING HEAT: RESISTANCE 260°C for 10 seconds after 120°C preheat cycle for 5 minutes.
TEMPERATURE CHARACTERISTIC -25°C to 85°C where inductance and Q shall not change more than 20%.
STORAGE TEMPERATURE Store at normal temperature (-5°C to + 35°C) and normal humidity(85% RH max) inoriginal package.
Do not expose to direct sunlight or harmful gas. This inductor can maintain its characteristics in a storage temperature from
-40°C to + 125°C for a period of 90 days.
HUMIDITY CHARACTERISTICS There is no change in performance at a humidity condition of 90-95% RH in 500 hours.
Measurement shall be made after 1 hour stabilization at room temperature.
HEAT RESISTANCE Subjected to 100°C for 1000 hours without change in appearance, deformation, or perf ormance.
Measurement shall be made after 1 hour stabilization at room temperature.
THERMAL SHOCK Subjected to 100 cycles at the following temperature range without a change in performance: -25°C for
1 hour + 100°C for 1 hour. Measurement shall be made after 1 hour stabilazation at room temperature.
TERMINAL STRENGTH Meets 3 lbs. pull test
RESISTANCE TO SOLVENT No change in appearance when dipped into alcohol or freon for 3 minutes.
MARKING Part is mar ked with inductance value in EIA code.
PACKAGING Tape and Reel only.
Daatsheeptd-hfptw/:wwD. aatShee4tUn.e/t

PagesPages 1
Télécharger [ LCM1210R2 ]


Fiche technique recommandé

No Description détaillée Fabricant
LCM1210R2 Molded Chip Inductor ETC
ETC

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche