|
|
Número de pieza | LV8081GQ | |
Descripción | Two channels Constant-current H-bridge Driver | |
Fabricantes | Sanyo Semicon Device | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de LV8081GQ (archivo pdf) en la parte inferior de esta página. Total 9 Páginas | ||
No Preview Available ! www.DataSheet.co.kr
Ordering number : ENA1550
Bi-CMOS LSI
LV8081GQ Two channels Constant-current
H-bridge Driver
Overview
The LV8081GQ is a two-channel constant-current driver that supports low-voltage operation. It is optimal for
constant-current drive of stepping motors (AF and zoom) in portable equipment such as camera cell phones.
Features
• Two channels constant-current H-bridge driver
• Built-in position detection comparator, SW for the photo reflector (independent control)
• Supports both 2 phase excitation drive and 1-2 phase excitation drive.
• Implemented in a low-power MOS IC process.
• Ultraminiature easy to solder UCT16 package (2.6 × 2.6 × 0.6mm)
• Built-in thermal shutdown circuit and Low voltage shutdown circuit.
• 1.8V input interface with battery supply.
• OUT1-3 short , OUT2-4 short and REG1-2 is short-circuited, and it is possible to correspond as 1ch driver.
Specifications
Absolute Maximum Ratings at Ta = -30 to 85°C(It becomes a design certification excluding 25℃.)
Parameter
Symbol
Conditions
Maximum supply voltage
Output voltage
Input voltage
Ground pin source current
VCC, VM max
VOUT max
VIN max
IGND
OUT1, OUT2, OUT3, OUT4
CONT, IN
Per channel
Allowable power dissipation
Pd max
Mounted on a circuit board.*
Operating temperature
Topr
Storage temperature
Tstg
* Specified circuit board : 40×50×0.8mm3 : 4-layer (2S2P) glass epoxy printed circuit board
Ratings
6.5
6.5
-0.3 to +6.5
400
700
-30 to +85
-40 to +150
Unit
V
V
V
mA
mW
°C
°C
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment (home appliances, AV equipment,
communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be
intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace
instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety
equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case
of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee
thereof. If you should intend to use our products for applications outside the standard applications of our
customer who is considering such use and/or outside the scope of our intended standard applications, please
consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our
customer shall be solely responsible for the use.
Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer's products or
equipment.
82609 SY 20071126-S00002 No.A1550-1/9
Datasheet pdf - http://www.DataSheet4U.net/
1 page www.DataSheet.co.kr
LV8081GQ
Continued from preceding page.
Pin No.
Pin Name
Description
12 COMPIN
Photo reflector position sensing comparator input
Equivalent Circuit
VCC
1kΩ
12
13 COMPOUT
Photo reflector position sensing comparator output
This pin serves as an open-collector output of the NPN
transistor.
1kΩ
13
GND
14 PI/PR
A switch, with NMOS open-drain output, used to turn
on/off the power supply of the position sensor unit. When
using this switch, connect the position sensor unit
between this pin and the VCC pin.
On/off control of this switch is accomplished by CONT
pin. Setting the CONT pin high turns on the switch.
6
VCC
GND
15 VCC
Power supply pin
Timing Chart
(1) Stepper motor timing chart
Timing chart for 2-phase drive
IN1
IN2
IN3
IN4
GND
Channel 1
output mode
Channel 2
output mode
Standby Forward
Reverse
Forward Reverse Forward
Standby
Standby
Forward
Reverse
Forward
Reverse Forward Standby
No.A1550-5/9
Datasheet pdf - http://www.DataSheet4U.net/
5 Page |
Páginas | Total 9 Páginas | |
PDF Descargar | [ Datasheet LV8081GQ.PDF ] |
Número de pieza | Descripción | Fabricantes |
LV8081GQ | Two channels Constant-current H-bridge Driver | Sanyo Semicon Device |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |