|
|
PDF LV5681P Data sheet ( Hoja de datos )
| Número de pieza | LV5681P | |
| Descripción | Multi-Power Supply System IC | |
| Fabricantes | Sanyo Semicon Device | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LV5681P (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
|
No Preview Available !
www.DataSheet.co.kr
Ordering number : ENA1902A
LV5681P
Monolithic Linear IC
For Car Audio Systems
Multi-Power Supply System IC
Overview
The LV5681P is a multi-power supply system IC that provides four regulator outputs and two high side switches as well as
a number of protection functions including overcurrent protection, overvoltage protection and overheat protection. It is an
optimal power supply IC for car audio and car entertainment systems and similar products.
Features
• Four regulator output systems
For microcontroller: 5.7V output voltage, 200mA maximum output current
For CD drive: 7.0V output voltage, 1300mA maximum output current
For illumination: 8 to 12V output voltage (output can be set with external resistors), 300mA maximum output current
For audio systems: 8 to 9V output voltage (output voltage can be set with external resistors), 300mA maximum
output current
• Two VCC-linked high side switch systems
EXT: 350mA maximum output current, 0.5V voltage difference between input and output.
ANT: 300mA maximum output current, 0.5V voltage difference between input and output.
• Two VDD 5V-linked high side switch systems
SW5V: 200mA maximum output current, 0.2V voltage difference between input and output.
ACC (accessory voltage detection output): 100mA maximum output current, 0.2V voltage difference between input
and output.
• Overcurrent protection function
• Overvoltage protection function, typ 21V (excluding VDD 5V output)
• Overheat protection function, typ 175ºC
• On-chip accessory voltage detection circuit
• P-channel LDMOS used for power output block
CAUTION)
The protection functions are provided in order to improve the ability of the ICs to withstand breakdown, and they are not intended to guarantee safety
when used under conditions outside the safe operating area or rated operating conditions.
Use of the ICs under any conditions exceeding the safe operating area or above the IOmax, and especially use in overcurrent protection areas or under
conditions in which they are subject to thermal protection, may reduce their reliability and result in permanent breakdown.
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment. The products mentioned herein
shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life,
aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system,
safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives
in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any
guarantee thereof. If you should intend to use our products for new introduction or other application different
from current conditions on the usage of automotive device, communication device, office equipment, industrial
equipment etc. , please consult with us about usage condition (temperature, operation time etc.) prior to the
intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely
responsible for the use.
Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer's products or
equipment.
O2611 SY 20111014-S00003/D2210 SY 20101201-S00005 No.A1902-1/14
Datasheet pdf - http://www.DataSheet4U.net/
1 page  
www.DataSheet.co.kr
Block Diagram
VCC
+B +
7
C1 C2
LV5681P
Over
Voltage
Protection
Start
up
Vref
EXT
out
ANT
out
-
+
CTRL1
(four-value control) 8
CTRL2
(three-value control)
6
OUTPUT
Control
GND
9
Thermal
Shut Down
ACC
10
+
-
Output Current Limit Circuit
-
+
-
+
-
+
Remote EXT(VCC-0.5V)
D1 350mA
15 +
C3 D2
ANT Remote (VCC-0.5V)
D3 300mA
14 +
C4 D4
ILM output (8V to 12V)
300mA
1+
R1 C5 C6
2 ILM_F
R2
AUDIO output (8V to 9V)
300mA
5+
R3 C7 C8
4 AUDIO_F
R4
CD output (7V)
1300mA
3+
C9 C10
VDD output (5.7V)
12 +
200mA
C11 C12
SW output (5.7V)
13
200mA
ACC output (5.7V)
11
100mA
Pin Function
Pin No. Pin name
1 ILM
Description
ILM output pin
ON when CTRL1 = M1, M2, H
8.0 to12.0V/300mA
2 ILM_F
ILM output voltage adjustment pin
Equivalent Circuit
7 VCC
1
2
9 GND
Continued on next page.
No.A1902-5/14
Datasheet pdf - http://www.DataSheet4U.net/
5 Page 
www.DataSheet.co.kr
• CTRL1 Application Circuit Example
R1
A
R2
B
CTRL1
500kΩ
LV5681P
(1) 3.3V input: R1 = 4.7kΩ, R2 = 10kΩ
AB
CTRL1
0V 0V
0V
0V 3.3V
1.05V
3.3V
0V
2.23V
3.3V
3.3V
3.20V
• CTRL2 Application Circuit Example
R3
C
R4
D
CTRL2
500kΩ
(1) 3.3V input: R3 = R4 = 4.7kΩ
AB
CTRL2
0V 0V
0V
0V 3.3V
1.61V
3.3V
0V
1.61V
3.3V
3.3V
3.29V
Caution for implementing LV5681P to a system board
In HZIP15J, the package used in this IC, there are several metal exposure other than the connection pins and heat-sinks as shown in
the following diagrams. In the diagrams, the electric potential of 2 and 3 are the same as Pin15 and Pin1, respectively. 2 (=Pin15) is
EXT pin and 3 (=Pin1) is ILM output (regulator). When the IC is implemented to the system, make sure that no attachment clamp
touches the exposed Pin1/ Pin15. When the exposed Pin1/ Pin15 touch the attachment clamp (same electrical potential as GND), ILM
output or VCC enter the same state as time when GND was shorted. The electric potential of the exposed metal connected to heat-sinks
1 is the same as that of sub board of the IC (GND). Therefore, even if the exposed metal and GND of the system board are adjacent to
each other, there should be no problem.
• HZIP15J external view
1
Heat-sink
Same potential
2
15PIN
Same potential
3
1PIN
Same potential
1
Heat-sink
Same potential
Heat-sink side
<Top view of HZIP15J>
:Metal exposure
Heat-sink side
1
Heat-sink
Same potential
:Metal exposure
<Side view of HZIP15J>
PS No.A1902-11/14
Datasheet pdf - http://www.DataSheet4U.net/
11 Page | ||
| Páginas | Total 14 Páginas | |
| PDF Descargar | [ Datasheet LV5681P.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LV5681P | Multi-Power Supply System IC | Sanyo Semicon Device |
| LV5681P | Multi-Power Supply System IC |  ON Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |