DataSheet.es    


PDF LC87F76C8A Data sheet ( Hoja de datos )

Número de pieza LC87F76C8A
Descripción 8-bit 1-chip Microcontroller
Fabricantes Sanyo Semicon Device　
Logotipo Sanyo Semicon Device Logotipo



Hay una vista previa y un enlace de descarga de LC87F76C8A (archivo pdf) en la parte inferior de esta página.


Total 24 Páginas

No Preview Available ! LC87F76C8A Hoja de datos, Descripción, Manual

www.DataSheet.co.kr
Ordering number : ENA0858
CMOS IC
LC87F76C8A FROM 128K byte, RAM 4K byte on-chip
8-bit 1-chip Microcontroller
Overview
The LC87F76C8A is an 8-bit microcomputer that, centered around a CPU running at a minimum bus cycle time of
83.3ns, integrates on a single chip a number of hardware features such as 128K-byte flash ROM (onboard
programmable), 4K-byte RAM, an on-chip debugger, an LCD controller/driver, a sophisticated 16-bit timer/counter
(may be divided into 8-bit timers), a 16-bit timer (may be divided into 8-bit timers or 8-bit PWMs), four 8-bit timers with
a prescaler, a base timer serving as a time-of-day clock, a day and time counter, a synchronous SIO interface (with
automatic block transmission/reception capabilities), an asynchronous/synchronous SIO interface, a UART interface (full
duplex), a 8-bit 12-channel AD converter, two 12-bit PWM channels, a high-speed clock counter, a system clock
frequency divider, a small signal detector, an infrared remote controller receiver function, and a 22-source 10-vector
interrupt feature.
Features
•Flash ROM
• Capable of on-board-programming with a wide range of souce voltages: 3.0 to 5.5V.
• Block-erasable in 2-byte units
• 131072 × 8 bits (LC87F76C8A)
•RAM
• 4096 × 9 bits (LC87F76C8A)
•Minimum Bus Cycle Time
• 83.3ns (12MHz)
• 125ns (8MHz)
• 250ns (4MHz)
VDD=3.0 to 5.5V
VDD=2.5 to 5.5V
VDD=2.2 to 5.5V
Note: The bus cycle time here refers to the ROM read speed.
* This product is licensed from Silicon Storage Technology, Inc. (USA), and manufactured and sold by
SANYO Semiconductor Co., Ltd.
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment (home appliances, AV equipment,
communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be
intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace
instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety
equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case
of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee
thereof. If you should intend to use our products for applications outside the standard applications of our
customer who is considering such use and/or outside the scope of our intended standard applications, please
consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our
customer shall be solely responsible for the use.
Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer's products or
equipment.
Ver.0.09
30409HKIM 20070523-S00003 No.A0858-1/24
Datasheet pdf - http://www.DataSheet4U.net/

1 page




LC87F76C8A pdf
www.DataSheet.co.kr
LC87F76C8A
•Standby Function
• HALT mode: Halts instruction execution while allowing the peripheral circuits to continue operation.
(Some parts of the serial transfer function stops operation.)
1) Oscillation is not stopped automatically.
2) Canceled by a system reset or occurrence of an interrupt
• HOLD mode: Suspends instruction execution and the operation of the peripheral circuits.
1) The CF, RC, X’tal, and multifrequency RC oscillators automatically stop operation.
2) There are three ways of resetting the HOLD mode.
(1) Setting the reset pin to the low level
(2) Setting at least one of the INT0, INT1, and INT2, pins to the specified level
(3) Having an interrupt source established at port 0
• X'tal HOLD mode: Suspends instruction execution and the operation of the peripheral circuits except the base timer
and infrared remote controller circuit.
1) The CF, RC, and multifrequency RC oscillators automatically stop operation
2) The state of crystal oscillation established when the X'tal HOLD mode is entered is retained.
3) There are five ways of resetting the X'tal HOLD mode.
(1) Setting the reset pin to the low level
(2) Setting at least one of the INT0, INT1, and INT2 pins to the specified level
(3) Having an interrupt source established at port 0
(4) Having an interrupt source established in the base timer circuit
(5) Having an interrupt source established in the infrared remote control receiver circuit
•On-chip Debugger
• Supports software debugging with the IC mounted on the target board.
•Package Form
• QIP80(14×14):
• TQFP80J(12×12):
Lead-free type
Lead-free type
•Development Tools
• On-chip debugger: TCB87-TypeB + LC87F76C8A
•Flash ROM Programming Board
Package
Programming Boards
QIP80(14×14)
W87F71256QF
TQFP80J(12×12)
W87F71256SQ
•Flash ROM Programmer
Maker
Flash Support Group, Inc
(Single)
Flash Support Group, Inc
(Gang)
Model
AF9708/AF9709/AF9709B
(including models manufactured by Ando
Electric Co., Ltd.)
AF9723 (main unit)
(including models manufactured by Ando
Electric Co., Ltd.)
AF9833 (unit)
(including models manufactured by Ando
Electric Co., Ltd.)
SANYO
SKK(SANYO FWS)
Note: Check for the latest version.
Supported Version (Note)
Application Version: After 1.04
Chip Data Version: After 2.09
Device
LC87F76C8A
LC87F76C8A
LC87F76C8A
•Same Package and Pin Assignment as Mask ROM Version.
1) LC877600 series options can be specified by using flash ROM data. Thus the board used for mass production can
be used for debugging and evaluation without modifications.
2) If the program for the mask ROM version is used, the size of the available ROM/RAM spaces is the same as
that of the mask ROM version.
No.A0858-5/24
Datasheet pdf - http://www.DataSheet4U.net/

5 Page





LC87F76C8A arduino
www.DataSheet.co.kr
LC87F76C8A
Absolute Maximum Ratings at Ta = 25°C, VSS1 = VSS2 = VSS3 = 0V
Parameter
Maximum supply
voltage
Symbol
VDD max
Pin/Remarks
Conditions
VDD1,VDD2, VDD3
VDD1=VDD2=VDD3
VDD[V]
min
-0.3
Specification
typ max
unit
+6.5
Supply voltage for
LCD
VLCD
V1/PL4, V2/PL5,
V3/PL6
VDD1=VDD2=VDD3
-0.3 VDD
Input voltage
Input/output
voltage
VI(1)
VIO(1)
• Port L
• XT1, CF1, RES
• Ports 0, 1, 3, 7, 8
• Ports A, B, C, D
• XT2
V
-0.3 VDD+0.3
-0.3 VDD+0.3
Peak output
current
IOPH(1)
Ports 0, 1
• CMOS output selected
• Per applicable pin
-10
IOPH(2)
Port 3
• CMOS output selected
• Per applicable pin
-20
IOPH(3)
Ports 71 to 73
Per applicable pin
-5
IOPH(4)
Ports A, B, C, D
Per applicable pin
-5
Average
output current
(Note 1-1)
IOMH(1)
IOMH(2)
Ports 0, 1
Port 3
• CMOS output selected
• Per applicable pin
• CMOS output selected
• Per applicable pin
-7.5
-15
IOMH(3)
Ports 71 to 73
Per applicable pin
-3
IOMH(4)
Ports A, B, C, D
Per applicable pin
-3
Total output
current
ΣIOAH(1)
Ports 0, 1, 31
Total of currents at all
applicable pins
-25
ΣIOAH(2)
Port 30
Total of currents at all
applicable pins
-15
ΣIOAH(3)
ΣIOAH(4)
Ports 0, 1, 3
Ports 71 to 73
Total of currents at all
applicable pins
Total of currents at all
applicable pins
-40
mA
-5
ΣIOAH(5)
Ports A, B
Total of currents at all
applicable pins
-25
ΣIOAH(6)
Ports C, D
Total of currents at all
applicable pins
-25
ΣIOAH(7)
Ports A, B, C, D
Total of currents at all
applicable pins
-45
Peak output
current
IOPL(1)
IOPL(2)
Ports 0, 1
Port 3
Per applicable pin
Per applicable pin
20
30
IOPL(3)
• Ports 7, 8
• XT2
Per applicable pin
10
IOPL(4)
Ports A, B, C, D
Per applicable pin
10
Average
output current
(Note 1-1)
IOML(1)
IOML(2)
IOML(3)
Ports 0, 1
Port 3
• Ports 7, 8
• XT2
Per applicable pin
Per applicable pin
Per applicable pin
15
20
7.5
IOML(4)
Ports A, B, C, D
Per applicable pin
7.5
Note 1-1: Average output current refers to the average of output currents measured for a period of 100ms.
Continued on next page.
No.A0858-11/24
Datasheet pdf - http://www.DataSheet4U.net/

11 Page







PáginasTotal 24 Páginas
PDF Descargar[ Datasheet LC87F76C8A.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
LC87F76C8A8-bit 1-chip MicrocontrollerSanyo Semicon Device
Sanyo Semicon Device
LC87F76C8A8-bit 1-chip MicrocontrollerON Semiconductor
ON Semiconductor

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

 Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

 Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar