|
|
Número de pieza | B154EW01_V9 | |
Descripción | LCD Module | |
Fabricantes | AUO | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de B154EW01_V9 (archivo pdf) en la parte inferior de esta página. Total 34 Páginas | ||
No Preview Available ! www.DataSheet4U.net
Product Specification
B154EW01 V9
AU OPTRONICS CORPORATION
Product Specification
15.4” WXGA Color TFT-LCD Module
Model Name: B154EW01 V9
Approved by
Prepared by
MDBU Marketing Division / AU Optronics corporation
Customer
Checked & Approved by
Document version 0.1
1/1
1 page www.DataSheet4U.net
Product Specification
B154EW01 V9
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human
earth when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was
taken out from the container, do not press the center of the CCFL Reflector edge.
Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT
Module may be damaged.
10)At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt
the Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be damaged.
12)Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local
ordinances or regulations for disposal.
13)Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source(,
IEC60950 or UL1950), or be applied exemption.
14)The LCD module is designed so that the CFL in it is supplied by Limited Current
Circuit(IEC60950 or UL1950). Do not connect the CFL in Hazardous Voltage Circuit.
Document version 0.1
5/5
5 Page www.DataSheet4U.net
Product Specification
B154EW01 V9
3. Functional Block Diagram
The following diagram shows the functional block of the 15.4 inches wide Color TFT/LCD Module:
(4 pairs LVDS)
RxIN0
RxIN1
RxIN2
RxCLKIN
LCD DRIVE
CARD
LCD
Controller
DC-DC
Converter
Ref circuit
VDD
GND
LCD Connector(30pin)
JAE FI-XB30S-HF10
Mating Housing JAE FI-X30H
Mating ContactFI-XC3-1-15000
X -D riv e r
TFT ARRAY/CELL
1280(R/G/B) x 3 x 800
Y-Driver
Backlight Unit
Lamp Connector(2pin)
JST BHSR-02VS-1
Mating Type SM02B-BHSS-1-TB
Document version 0.1
11/11
11 Page |
Páginas | Total 34 Páginas | |
PDF Descargar | [ Datasheet B154EW01_V9.PDF ] |
Número de pieza | Descripción | Fabricantes |
B154EW01-V0 | LCD Module | AUO |
B154EW01-V1 | LCD Module | AUO |
B154EW01-V8 | LCD Module | AUO |
B154EW01-V9 | LCD Module | AUO |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |