|
|
PDF LTM10C348U Data sheet ( Hoja de datos )
| Número de pieza | LTM10C348U | |
| Descripción | LCD Module | |
| Fabricantes | Toshiba | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LTM10C348U (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
LT M 1 0 C 3 4 8 U
APPROVAL SIGNATURE
SPECIFICATION
FOR
TOSHIBA TFT-LCD MODULE
LT M 1 0 C 3 4 8 U
SPECIFICATION No. :
N L - LT M 1 0 C 3 4 8 U - 11
DATE OF ISSUE : 2000-07-26
(DATE OF EXPIRY : 2003-07-26)
T. Nakagawa
Senior Manager
Liquid Crystal Display
Quality Assurance Dept.
Liquid Crystal Display Div.
<Engineering Department to contact as per SPECIFICATION>
Liquid Crystal Display Device Marketing & Engineering Dept.
Liquid Crystal Display Div.
TOSHIBA Corporation
1-9-2, Hatara-cho, Fukaya-shi, Saitama, 366-8510, JAPAN
www.DataSheet4U.net
1 page  
Specification No.
Sheet 4
For Installation in Assembly
(1) The C-MOS LSIs used in LCD module are very sensitive to ESD (Electro-static Discharge).
Ambient humidity of working area is recommended to be higher than 50%(RH).
Person handling LCD modules should be grounded with wrist band. Tools like soldering iron and screwdriver, and
working benches should be grounded.
The grounding should be done through a resistor of 0.5-1Mohms in order to prevent spark of ESD.
(2) When remove protection film from LCD panel, peer off the film slowly (more than three seconds) from the edge of the
panel, using a soft-pointed tweezers covered by Teflon or adherent tape.
(3) Reduce dust level in working area. Especially the level of metal particle should be decreased.
Use fingerstalls or soft and dust-free gloves in order to keep clean appearance of LCD module when handled for
incoming inspection and assembly.
*(4) When LCD panel becomes dirty, wipe off the panel surface softly with absorbent cotton or another soft cloth.
If necessary, breathe upon the panel surface and then wipe off immediately and softly again.
If the dirt can not be wiped off, absorbent cotton wetted a little with normal-hexane or petroleum benzine can be used for
wiping the panel.
Be careful not to spill this solvent into the inside of LCD module. Driver ICs and PCB area used inside LCD module may
be damaged by the solvent.
*(5) AVOID THE CONDENSATION OF WATER
Wipe off a spot or spots of water of mist and chemicals of mist on LCD panel softly with absorbent cotton or another
cloth as soon as possible if happened, otherwise discoloration or stain may be caused. If water invade into LCD module,
it may cause LCD module damages.
*(6) Do not expose LCD module to the gas (which is not normally contained in the atmosphere), it may cause
mis-operation or defects.
*(7) DO NOT APPLY MECHANICAL FORCES.
Do not bend or twist LCD module even momentary when LCD module is installed an enclosure of the system. Bending
or twisting LCD module may cause its damages.
Make sure to design the enclosure that bending/twisting forces are not applied to LCD module when it is installed in the
system.
Refrain from strong mechanical shock like dropping from the working bench or knocking against hard object.
These may cause glass of the panel crack, damage of FL or other mis-operation.
*(8) Refrain from excessive force like pushing the surface of LCD panel. This may cause damage of the panel or
electrical parts on PCB.
*(9) Do not put heavy object such as tools, books, etc., and do not pile up LCD modules.
Be careful not to touch surface of the polarizer laminated to the panel with any hard and sharp object. The polarizer is so
soft that it can easily scratched, even the protect film covers it.
(10) When inserting or disconnecting the connectors to LCD module, be sure not to apply force against PCB, nor connecting
cables, otherwise internal connection of PCB and TAB drivers may be damaged.
Do not fasten screws while putting cables like those for interface or FL between LCD module and the enclosure.
Make sure to insert the module FL connector to the inverter connector in correct position.
If incorrect, this may cause smoke or burn of electrical parts by high voltage of FL circuit.
LIQUID CRYSTAL DISPLAY DIVISION
Date:2000-07-26
Date:
New No. NL-LTM10C348U-11U
Old No.
←# Special ←& Addition ← Change
5 Page 
Specification No.
(back figure)
Sheet 10
Unit : mm
Standard Tolerance :± 0.5
LIQUID CRYSTAL DISPLAY DIVISION
Date:2000-07-26
Date:
New No. NL-LTM10C348U-11U
Old No.
←# Special ←& Addition ← Change
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet LTM10C348U.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LTM10C348S | LIQUID CRYSTAL DISPLAY DIVISION PRODUCT INFORMATION |  Toshiba Semiconductor |
| LTM10C348U | LCD Module | Toshiba |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |