|
|
PDF N121X5-L06 Data sheet ( Hoja de datos )
| Número de pieza | N121X5-L06 | |
| Descripción | LCD Module | |
| Fabricantes | CHI MEI | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de N121X5-L06 (archivo pdf) en la parte inferior de esta página. Total 29 Páginas | ||
|
No Preview Available !
Doc No.: 1406X064
Issued Date: Jan. 10, 2007
Model No.: N121X5 -L06
Approval
TFT LCD Approval Specification
MODEL NO.: N121X5 -L06
Customer : Lenovo
Approved by :
Note :
2007-01-11
19:10:37 CST
2007-01-10
18:18:54 CST
Approve by Dept. tomy_chen(
Mgr.(QA RA)
/52720/54140/43150)
Approve by
Director
teren_lin(
/56910/36064)
Department
Manager(QA RA)
Director
Accept
Accept
www.DataSheet4U.net
1 / 29
Version 3.1
1 page  
Doc No.: 1406X064
Issued Date: Jan. 10, 2007
Model No.: N121X5 -L06
Approval
2. ABSOLUTE MAXIMUM RATINGS
2.1 ABSOLUTE RATINGS OF ENVIRONMENT
Item
Storage Temperature
Operating Ambient Temperature
Shock (Non-Operating)
Vibration (Non-Operating)
Symbol
TST
TOP
SNOP
VNOP
Value
Min. Max.
Unit
Note
-20
+60 ºC
(1)
0 +50 ºC (1), (2)
- 210/50 G (3), (5)
- 1.5 G (4), (5)
Note (1) Temperature and relative humidity range is shown in the figure below.
(a) 90 %RH Max. (Ta 40 ºC).
(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).
(c) No condensation.
Relative Humidity (%RH)
100
95
80
60 Operating Range
40
20
8
5 Storage Range
-40 -20
0 20 40 60 80
Temperature (ºC)
Note (2) The temperature of panel surface should be 0 ºC Min. and 50 ºC Max.
Note (3) 1 time for ± X, ± Y, ± Z. for Condition (210G / 3ms) is half Sine Wave, Condition (50G / 18ms) is
Rectangle Wave,
Note (4) 10 ~ 200 Hz, 0.5 Hr / Cycle, 1 cycles for each X, Y, Z.
Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough
so that the module would not be twisted or bent by the fixture. The fixing condition is shown as
below:
At Room Temperature
Side Mount Fixing Screw
Gap=2mm
LCD Module
Bracket
5 / 29
Side Mount Fixing Screw
Stage
Version 3.1
5 Page 
Doc No.: 1406X064
Issued Date: Jan. 10, 2007
Model No.: N121X5 -L06
Approval
Note (7) About operating current min 2.0mA , lamp maker has some advice as below
(Reference) Light quantity adjustment method
Explanation and comparison of the kind of tone light:
Lamp current wave-like by the adjustment of the current.
P-P LEVEL DOWN
Tone light
Lamp current wave-like by the adjustment of the burst.
P-P LEVEL =
OFF:20%
ON:80%
Comparative table
Method
current
burst
Backlight efficiency (INV LAMP)
Good ( 75 % 85% )
Bad ( 65 % 75% )
Tone light rate (%)
58
10
Method of case that Lamp current MIN2.0mA is controlled.
Circuitry
Complicated
Easy
It is the setting of minimum 2mA (MIN) to Lamp current 6.0mA in the lamp specification. The burst is
excellent for circuitry. The marker proposes that pays attention to the following contents.
11 / 29
Version 3.1
11 Page | ||
| Páginas | Total 29 Páginas | |
| PDF Descargar | [ Datasheet N121X5-L06.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| N121X5-L01 | TFT LCD |  Chi Mei |
| N121X5-L02 | TFT Liquid Crystal Display module | Chi Mei |
| N121X5-L03 | LCD Module | Chi Mei |
| N121X5-L04 | TFT LCD | Chi Mei |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |