DataSheet.es    


PDF LXMG1643-12-61 Data sheet ( Hoja de datos )

Número de pieza LXMG1643-12-61
Descripción CCFL Programmable Inverter Module
Fabricantes Microsemi Corporation 
Logotipo Microsemi Corporation Logotipo



Hay una vista previa y un enlace de descarga de LXMG1643-12-61 (archivo pdf) en la parte inferior de esta página.


Total 6 Páginas

No Preview Available ! LXMG1643-12-61 Hoja de datos, Descripción, Manual

PanelMatch™
LXMG1643-12-61
TM ® 12V Quad 6W CCFL Programmable Inverter Module
PRODUCTION DATASHEET
DESCRIPTION
The LXMG1643-12-61 is a Quad 6W The resultant “burst drive” that
Output Direct Drive™ CCFL (Cold energizes the lamp was designed
wwwC.DatahtaoSdheeet4UF.nleutorescent Lamp) Inverter specifically to ensure that no premature
Module specifically designed for driving lamp degradation occurs, while allowing
LCD backlight lamps. It is ideal for significant power savings at lower dim
driving typical 12.1” to 18.1” TFT panels. levels.
LXMG1643 modules provides the The modules convert DC voltage from
designer with a vastly superior display the system battery or AC adapter directly
brightness range then typical with analog to high frequency, high-voltage waves
(amplitude control) dimming.
required to ignite and operate CCFL
The inverter includes a dimming input lamps.
that permits brightness control from either The LXMG1643-12-61 inverter is
a DC voltage source or a PWM signal or intended for panel assemblies where lamp
external Potentiometer. The maximum pairs share close proximity with one
output current is externally programmable another. The LXMG1643-12-62 inverter
over a range of 10 to 16mA (per lamp pair) should be considered for panel
in 2mA steps to allow the inverter to applications with individual lamp
properly match to a wide array of LCD connections or where lamps are spaced
panel lamp current specifications.
well apart from each other.
RangeMAX Digital Dimming Other benefits of this new topology
Technique provides flicker-free brightness are stable fixed-frequency operation,
control in any wide range typically (50:1+) secondary-side strike-voltage regulation
dimming application.
and both open/shorted lamp protection
with fault timeout.
IMPORTANT: For the most current data consult MICROSEMI’s website: http://www.microsemi.com
Protected By U.S. Patents: 5,923,129; 5,930,121; 6,198,234; Patents Pending
KEY FEATURES
ƒ Externally Programmable
Maximum Output Current
ƒ Easy to Use Brightness
Control
ƒ RangeMAX Wide Range
Dimming
ƒ Output Short-Circuit Protection
and Automatic Strike-Voltage
Regulation and Timeout
ƒ Fixed Frequency Operation
ƒ Rated From -20 to 70°C
ƒ UL 60950 E175910
ƒ RoHS Compliant
APPLICATIONS
ƒ High Brightness Displays
ƒ Desktop Displays
ƒ Industrial Display Controls
BENEFITS
ƒ Smooth, Flicker Free 2%-
100% Full-Range
Brightness Control
ƒ Programmable output
current allows inverter to
mate with a wide variety of
LCD panel’s specifications
PRODUCT HIGHLIGHT
Universal Dimming Input PWM, VDC, or Potentiometer
DC
Voltage
Source
Potentiometer
PWM
Signal
Selectable Maximum Output Current 10mA to 16mARMS
W
PART NUMBER
LXMG1643-12-61
Copyright © 2005
Rev. 1.0a, 2006-11-16
PACKAGE ORDER INFO
OUTPUT CONNECTORS
Two JST SM04(4.0)B-BHS-1-TB(LF)(SN) or Yeon Ho 20015WR-
07A00
INVERTER MATES DIRECTLY
TO PANEL CONNECTORS
JST BHR-04VS-1
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 1

1 page




LXMG1643-12-61 pdf
PanelMatch™
LXMG1643-12-61
TM ® 12V Quad 6W CCFL Programmable Inverter Module
PRODUCTION DATASHEET
TYPICAL APPLICATION
DAC or
Pot
0.4to5V
2.0V
20K
1.8K
BRITE
12V
VIN1
V Hx
V Hx
LXMG1643-12-61
SLEEP
SET1 SET2
NC NC
GND V LO
One
of
two
Figure 1 – Brightness Control
(Output current set to maximum)
PWM Signal
from System
BRITE
P.W.
10µs to 125µS
LXMG1643-12-61
0 < P.W. < 100% of period
Figure 1A – PWM Brightness Control
BRITE
12V
V IN1
LXMG1643-12-61
SLEEP
SET 1
SET 2
GND
One
of two
L L 10.0mARMS
L H 12.0mARMS
H L 14.0mARMS
H H 16.0mARMS
L=GND; H=Open
Figure 2 – Max Output Current (Two Lamps)
(SET1 and SET2 Inputs)
ƒ The brightness control may be a voltage output DAC or
other voltage source, a digital pot or 20K manual pot. The
inverter contains an internal 10K pull-up to 3V to bias the
pot add a 1.8K resistor to set the lower threshold voltage.
A 3.3V Logic Level PWM signal from a micro-controller
may also be used as shown in Figure 1A.
ƒ If you need to turn the inverter ON/OFF remotely, connect
to TTL logic signal to the SLEEP input.
ƒ Connect VHI to high voltage wire from the lamp. Connect
VLO to the low voltage wire (wire with thinner insulation).
Never connect VLO to circuit ground as this will defeat
lamp current regulation. If both lamp wires have heavy
high voltage insulation, connect the longest wire to VLO.
This wire is typically white.
ƒ Use the SET1 and SET2 (see Figure 2) inputs to select the
desired maximum output current. Using these two pins in
combination allows the inverter to match a wide variety of
panels from different manufactures. Generally the best
lamp lifetime correlates with driving the CCFL at the
manufactures nominal current setting. However the SET1
and SET2 inputs allow the user the flexibility to adjust the
current to the maximum allowable output current to
increase panel brightness at the expense of some reduced
lamp life.
ƒ Although the SET pins are designed such that just leaving
them open or grounding them is all that is needed to set the
output current, they can also be actively set. Using a open
collector or open drain logic signal will allow you to
reduce the lamp current for situations where greater dim
range is required, as an example in nighttime situations. In
conjunction with a light sensor or other timer the panel
could be set to higher brightness (maximum output
current) for daytime illumination and lower brightness
(minimum or typical output current) at nighttime. Since
the dim ratio is a factor of both the burst duty cycle and the
peak output current, using this technique the effective dim
ratio can be increased greater than the burst duty cycle
alone. Conversely the SET inputs could be used to
overdrive the lamp temporarily to facilitate faster lamp
warm up at initial lamp turn on. Of course any possible
degradation on lamp life from such practices is the users
responsibility since not all lamps are designed to be
overdriven.
ƒ The inverter has a built in fault timeout function. If the
output return is open (lamp disconnected or broken) or
shorted the inverter will attempt to strike the lamp for
several seconds. After about a second without success the
inverter will shutdown. In order to restart the inverter it is
necessary to toggle the sleep input or cycle the VIN1 input
supply. In the timeout shutdown mode input drain current
will be about 8mA.
Copyright © 2005
Rev. 1.0a, 2006-11-16
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 5

5 Page










PáginasTotal 6 Páginas
PDF Descargar[ Datasheet LXMG1643-12-61.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
LXMG1643-12-61CCFL Programmable Inverter ModuleMicrosemi Corporation
Microsemi Corporation
LXMG1643-12-62CCFL Programmable Inverter ModuleMicrosemi Corporation
Microsemi Corporation
LXMG1643-12-63CCFL Programmable Inverter ModuleMicrosemi Corporation
Microsemi Corporation
LXMG1643-12-64CCFL Programmable Inverter ModuleMicrosemi Corporation
Microsemi Corporation

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar