HL1606 Datasheet PDF - ETC
| Part Number | HL1606 | |
| Description | LED driver IC | |
| Manufacturers | ETC | |
| Logo |  |
|
|
There is a preview and HL1606 download ( pdf file ) link at the bottom of this page. Total 6 Pages | ||
Preview 1 page No Preview Available !
HL1606
www.DataSheet4U.com
DESCRIPTION
HL1606 is a LED driver IC with SPI controlled. We can get “complex mode changes” by fewer data.
FEATURES
NMOS output
SPI controlled，plus synchronization speed control port: S-I
PWM output,frequency:500Hz
With a internal “change model” unit，only data calls, reducing the amount of data.
Speed control bit，can speed up “changes in a pixel” rate of 2 times.
Latch enable bit，concatenated string at a point can be read or not read data.
Built-6 road, drive two pixels（three-output get a pixel）
Pin definition
No. Name
Description
No. Name
Description
1
S-I Sync / speed clock input
7
D-O
Data buffer output
2 D-I
Data input
8 S-O Sync / speed clock buffer output
3 CK-I
Clock input
9 GND
GND
4 L-I
Latch signal input
10~12 B3~B1
3 way drive output
5 L-O Latch signal buffer output 13~15 A3~A1
3 way drive output
6 CK-O
Clock buffer output
16 VDD
VDD
Data format
D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 HIGH
A1~A3 LED Control data-1
B1~B3 LED Control date-2
Data format of A1-A3 LED Control data-1(B1-B3 LED Control data-2 can refer it)
D1（D9） D2（D10）
A1（B1）Control bit
D3（D11） D4（D12）
A2（B2）Control bit
D5（D13） D6（D14）
A3（B3）Control bit
D7（D15） D8（D16）
Control bit
Latch
of speed enable bit
Page 1 / 6
|
| |
 
www.DataSheet4U.com
then input ”0” to the end is okay(red to yellow gradually). Clock signal has been sent to CK_I, sent a “1” to L_I
after 8 clock signal. Change once the signal of S_I, the output series change once. A clock cycle in S_I,.
output is keep in 512Hz refresh frequency, to maintain the same level(series) of output duty cycle refresh. If
no data sent to S_I, output will remain the same duty cycle refresh. Just finished in a color change, change
the data of D-I.
Application
+5V
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
VCC
78L0 5
OUT
OUT
MOSFET N
(1)
U1
S_I
D_I
CK_I
L_I
104
※
VDD
S_O
D_O
CK_O
L_O
B3
B2
B1
A3
A2
GND A1
47uF
104
※
VDD
U2
S_O
D_O
CK_O
L_O
B3
B2
B1
A3
A2
GND A1
(2) (3)
+5V
47uF
104
※
VDD
U3
S_O
D_O
CK_O
L_O
B3
B2
B1
A3
A2
GND A1
47uF
→
UN
VDD
104
※
S_O
D_O
CK_O
L_O
B3
B2
B1
A3
A2
GND A1
R#
47uF
(4)
Application Notes
1. Picture(1),1st connection method: triode will not connect to output of IC, output current reach 30Ma,output
can connect to two-ways, ensure that the output voltage must be less than 6V.
2. Picture(2), 2nd connection method: triode connect to output of IC. Because the NPN-type transistor at the
base took on the extreme pull-up resistor, the “output duty cycle of IC” and the” LED brightness” is
inversely proportional to. When the IC doesn’t output, the transistor fully conducting, LED full-bright.
Page 5 / 6
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for HL1606 electronic component. |
| Information | Total 6 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ HL1606.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| HL1606 | The function is LED driver IC. ETC | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
HL16
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||