|
|
PDF FSP3126 Data sheet ( Hoja de datos )
| Número de pieza | FSP3126 | |
| Descripción | WIDE INPUT 2A STEP DOWN CONVERTER | |
| Fabricantes | FOSLINK SEMICONDUCTOR | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de FSP3126 (archivo pdf) en la parte inferior de esta página. Total 9 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
WIDE INPUT 2A STEP DOWN CONVERTER
FEATURES
z 2A Output Current
z Up to 95% Efficiency
z 4.75V to 20V Input Range
z 8µA Shutdown Supply Current
z 410kHz Switching Frequency
z Adjustable Output Voltage
z Cycle-by-Cycle Current Limit Protection
z Thermal Shutdown Protection
z Frequency Foldback at Short Circuit
z Stability with Wide Range of Capacitors,
Including Low ESR Ceramic Capacitors
z SOP8L Package
FSP3126
GENERAL DESCRIPTION
The FSP3126 is a current-mode step-down DC/DC
converter that generates up to 2A of output current at
410kHz switching frequency. The device utilizes
ISOBCD20 process for operation with input voltages
up to 20V.
Consuming only 8µA in shutdown mode, the
FSP3126 is highly efficient with peak operating
efficiency at 95%. Protection features include
cycle-by-cycle current limit, thermal shutdown, and
frequency foldback at short circuit.
The FSP3126 is available in a SOP8L package and
requires very few external devices for operation.
Typical Application
z TFT LCD Monitors
z Portable DVDs
z Car-Powered or Battery-Powered Equipments
z Set-Top Boxes
z Telecom Power Supplies
z DSL and Cable Modems and Routers
z Termination Supplies
PIN ASSIGNMENT
(Top View)
BS 1
IN 2
SW 3
G4
8 N/C
7 EN
FSP3126
6 COMP
5 FB
PIN DESCRIPTION
Name
BS
IN
SW
G
FB
No.
1
2
3
4
5
COMP
6
EN 7
N/C 8
Description
Bootstrap. This pin acts as the positive rail for the high-side switch’s gate driver.
Connect a 10nF capacitor between BS and SW.
Input Supply. Bypass this pin to G with a low ESR capacitor. See Input Capacitor
in the Application Information section.
Switch Output. Connect this pin to the switching end of the inductor.
Ground.
Feedback Input. The voltage at this pin is regulated to 1.293V. Connect to the
resistor divider between output and ground to set output voltage.
Compensation Pin. See Stability Compensation in the Application Information
section.
Enable Input. When higher than 1.3V, this pin turns the IC on. When lower than
0.7V, this pin turns the IC off. Output voltage is discharged when the IC is off.
When left unconnected, EN is pulled up to 4.5V tip with a 2µA pull up current.
Not Connected.
1/9 2007-5-28
1 page  
www.DataSheet4U.com
WIDE INPUT 2A STEP DOWN CONVERTER
FSP3126
For ceramic output capacitors, typically choose a capacitance of about 22µF. For tantalum or electrolytic capacitors,
choose a capacitor with less than 50mΩ ESR.
Rectifier Diode
Use a Schottky diode as the rectifier to conduct current when the High-Side Power Switch is off. The Schottky diode
must have a current rating higher than the maximum output current and a reverse voltage rating higher than the
maximum input voltage.
Stability Compensation
CCOMP2 is needed only for high ESR output capacitor
Figure 2. Stability Compensation
The feedback loop of the IC is stabilized by the components at the COMP pin, as shown in Figure 2. The DC loop gain
of the system is determined by the following equation:
AVDC
=
1.3V
IOUT
AVEA G COMP
(4)
The dominant pole P1 is due to CCOMP:
fP1
=
G EA
2 πAVEA C C OM P
(5)
The second pole P2 is the output pole:
fP2
=
IOUT
2πVOUT COUT
(6)
The first zero Z1 is due to RCOMP and CCOMP:
fZ1
=
1
2πRCOMP CCOMP
(7)
And finally, the third pole is due to RCOMP and CCOMP2 (if CCOMP2 is used):
fP3
1
= 2πRCOMP CCOMP2
(8)
The following steps should be used to compensate the IC:
STEP1. Set the crossover frequency at 1/10 of the switching frequency via RCOMP:
RCOMP
=
2πVOUT COUT fSW
10GEAGCOMP • 1.3V
(9)
but limit RCOMP to 15kΩ maximum.
STEP2. Set the zero fZ1 at 1/4 of the crossover frequency. If RCOMP is less than 15kΩ, the equation for CCOMP is:
CCOMP
= 1.8 × 10 −5
RCOMP
(F )
(10)
If RCOMP is limited to 15kΩ, then the actual crossover frequency is 3.4 / (VOUTCOUT). Therefore:
CCOMP = 1.2 ×10 −5 VOUT COUT
(F )
(11)
STEP3. If the output capacitor’s ESR is high enough to cause a zero at lower than 4 times the crossover frequency,
an additional compensation capacitor CCOMP2 is required. The condition for using CCOMP2 is:
R ESRCOUT
≥
Min
⎛
⎜⎜⎝
1
.1 ×10
COUT
−6
,0.012 • VOUT
⎞
⎟⎟⎠
(Ω)
(12)
5/9 2007-5-28
5 Page | ||
| Páginas | Total 9 Páginas | |
| PDF Descargar | [ Datasheet FSP3126.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| FSP3122 | 150KHZ 3A PWM BUCK DC/DC CONVERTER | FOSLINK SEMICONDUCTOR |
| FSP3123 | 150KHZ 3A PWM BUCK DC/DC CONVERTER | FOSLINK SEMICONDUCTOR |
| FSP3124 | 150KHZ 3A PWM BUCK DC/DC CONVERTER | FOSLINK SEMICONDUCTOR |
| FSP3125 | 150KHZ 2A PWM BUCK DC/DC CONVERTER | FOSLINK SEMICONDUCTOR |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |