DataSheetWiki


CAT5115 fiches techniques PDF

Catalyst Semiconductor - 32-Tap Digitally Programmable Potentiometer (DPP)

Numéro de référence CAT5115
Description 32-Tap Digitally Programmable Potentiometer (DPP)
Fabricant Catalyst Semiconductor 
Logo Catalyst Semiconductor 





1 Page

No Preview Available !





CAT5115 fiche technique
www.DataSheet4U.com
CAT5115
32-Tap Digitally Programmable Potentiometer (DPP™)
FEATURES
„ 32-position linear taper potentiometer
„ Low power CMOS technology
„ Single supply operation: 2.5V – 6V
„ Increment up/down serial interface
„ Resistance values: 10k, 50kand 100k
„ Available in PDIP, SOIC, TSSOP, MSOP and
space saving 2 x 2.5mm TDFN packages
APPLICATIONS
„ Automated product calibration
„ Remote control adjustments
„ Offset, gain and zero control
„ Tamper-proof calibrations
„ Contrast, brightness and volume controls
„ Motor controls and feedback systems
„ Programmable analog functions
For Ordering Information details, see page 13.
FUNCTIONAL DIAGRAM
VCC
U/D
Control
INC and
Power-On
CS Recall
GND
RH
RW
RL
General
VDD
GND
CS
INC
U/D
DESCRIPTION
The CAT5115 is a single digitally programmable
potentiometer (DPP™) designed as a electronic
replacement for mechanical potentiometers and trim
pots. Ideal for automated adjustments on high volume
production lines, they are also well suited for
applications where equipment requiring periodic
adjustment is either difficult to access or located in a
hazardous or remote environment.
The CAT5115 contains a 32-tap series resistor array
connected between two terminals RH and RL. An
up/down counter and decoder that are controlled by
three input pins, determines which tap is connected to
the wiper, RW. The wiper is always set to the mid
point, tap 15 at power up. The tap position is not
stored in memory. Wiper-control of the CAT5115 is
accomplished with three input control pins, C¯¯S, U/D¯,
and I¯N¯C¯. The I¯N¯C¯ input increments the wiper in the
direction which is determined by the logic state of the
U/D¯ input. The C¯¯S input is used to select the device.
The digitally programmable potentiometer can be used
as a three-terminal resistive divider or as a two-terminal
variable resistor. DPPs bring variability and program-
mability to a wide variety of applications including
control, parameter adjustments, and signal processing.
For a pin-compatible device that recalls a stored tap
position on power-up refer to the CAT5114 data sheet.
RH/VH
RH
RW/VW
RW
RL/VL
Detailed
RL
Electronic Potentiometer
Implementation
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
1
Doc. No. MD-2117 Rev. H

PagesPages 14
Télécharger [ CAT5115 ]


Fiche technique recommandé

No Description détaillée Fabricant
CAT511 8-Bit Digital POT with Independent Reference Inputs Catalyst Semiconductor
Catalyst Semiconductor
CAT5110 32-tap Digital Potentiometers ON Semiconductor
ON Semiconductor
CAT5110 (CAT5110 - CAT5125) Digitally Programmable Potentiometers Catalyst Semiconductor
Catalyst Semiconductor
CAT5111 100-Tap Digitally Programmable Potentiometer ON Semiconductor
ON Semiconductor

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche