DataSheetWiki


PCA9530 fiches techniques PDF

NXP Semiconductors - 2-bit I2C-bus LED dimmer

Numéro de référence PCA9530
Description 2-bit I2C-bus LED dimmer
Fabricant NXP Semiconductors 
Logo NXP Semiconductors 





1 Page

No Preview Available !





PCA9530 fiche technique
PCA9530
2-bit I2C-bus LED dimmer
Rev. 03 — 26 February 2009
www.DataSheet4U.com
Product data sheet
1. General description
The PCA9530 is a 2-bit I2C-bus and SMBus I/O expander optimized for dimming LEDs in
256 discrete steps for Red/Green/Blue (RGB) color mixing and backlight applications.
The PCA9530 contains an internal oscillator with two user programmable blink rates and
duty cycles coupled to the output PWM. The LED brightness is controlled by setting the
blink rate high enough (> 100 Hz) that the blinking cannot be seen and then using the
duty cycle to vary the amount of time the LED is on and thus the average current through
the LED.
The initial setup sequence programs the two blink rates/duty cycles for each individual
PWM. From then on, only one command from the bus master is required to turn individual
LEDs ON, OFF, BLINK RATE 1 or BLINK RATE 2. Based on the programmed frequency
and duty cycle, BLINK RATE 1 and BLINK RATE 2 will cause the LEDs to appear at a
different brightness or blink at periods up to 1.69 second. The open-drain outputs directly
drive the LEDs with maximum output sink current of 25 mA per bit and 50 mA per
package.
To blink LEDs at periods greater than 1.69 second, the bus master (MCU, MPU, DSP,
chip set, etc.) must send repeated commands to turn the LED on and off as is currently
done when using normal I/O Expanders like the NXP Semiconductors PCF8574 or
PCA9554. Any bits not used for controlling the LEDs can be used for General Purpose
parallel Input/Output (GPIO) expansion which provides a simple solution when additional
I/O is needed for ACPI power switches, sensors, push buttons, alarm monitoring, fans,
etc.
The active LOW hardware reset pin (RESET) and Power-On Reset (POR) initialize the
registers to their default state causing the bits to be set HIGH (LED off).
One hardware address pin on the PCA9530 allows two devices to operate on the same
bus.
2. Features
I 2 LED drivers (on, off, flashing at a programmable rate)
I 2 selectable, fully programmable blink rates (frequency and duty cycle) between
0.591 Hz and 152 Hz (1.69 seconds and 6.58 milliseconds)
I 256 brightness steps
I Input/output not used as LED drivers can be used as regular GPIOs
I Internal oscillator requires no external components
I I2C-bus interface logic compatible with SMBus
I Internal power-on reset

PagesPages 24
Télécharger [ PCA9530 ]


Fiche technique recommandé

No Description détaillée Fabricant
PCA9530 2-bit I2C-bus LED dimmer NXP Semiconductors
NXP Semiconductors
PCA9531 8-bit I2C LED dimmer NXP Semiconductors
NXP Semiconductors
PCA9531BS 8-bit I2C LED dimmer NXP Semiconductors
NXP Semiconductors
PCA9531D 8-bit I2C LED dimmer NXP Semiconductors
NXP Semiconductors

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche